HDA2130Z04WW Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cliff from Atlantic Beach, NC
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
The pump seal was leaking.
Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Hesperia, MI
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Leaking from the pump
Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Victor, ID
- Parts Used:
- WD21X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
dishwasher would not drain water at end of cycle
I replaced the drain solenoid which was about $35 dollars. It consisted of a couple of springs, a hanging bracket, a plastic part and couple of screws to fasten the bracket and the solenoid of course. My dishwasher now drains the water. Much easier fix than i thought it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Pembroke Pines, FL
- Parts Used:
- WD16X10011
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Could not get the arm to close.
I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.
Thanks for your help.
Thanks for your help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Crystal from Madison Heights, MI
- Parts Used:
- WD21X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The timer stopped working
I took the inside of the door off of the dishwasher and disconnected the timer, ordered the new timer and with a couple of screws and the attachment of 3 wires I was back in business! Now my dishwasher is working better than ever!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Bastrop, TX
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Old pump was making noise and leaking.
Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luke from Soledad, CA
- Parts Used:
- WD21X10060
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dishwasher wouldn't drain
After checking to make sure the filter wasn't clogged I removed the faceplate and, poking around a bit realized that the solenoid that actuates the drain valve was jammed. Removing it was was simply a matter of removing a pin and two screws. I reattached the new part, the only difficult part was holding the part in place while reattaching a few springs. Closed it up and its working like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Medford, NY
- Parts Used:
- WD21X10060
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
water was not draining
Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick from Glen Ellyn, IL
- Parts Used:
- WD27X10170
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Missing when my daughter purchased her townhouse.
1. Installed temporary plywood cover to prevent new puppy from wandering under dishwasher.
2. Ordered new toe kick; arrived in two days.
3. Unscrewed plywood.
4. Installed new toe kick with original screws.
5. Crossed project off to-do list.
2. Ordered new toe kick; arrived in two days.
3. Unscrewed plywood.
4. Installed new toe kick with original screws.
5. Crossed project off to-do list.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Kernersville, NC
- Parts Used:
- WD21X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Timer had stopped working.
Removed the 6 screws and took off the inside pannel. Removed 2 screws that secured the timer.Unplugged old timer leads and put the new one in reverse sequence. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Franklin, TN
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rinse Aid Fill Cap missing from dishwasher in condo I just bought.
Opened package, removed cap and screwed it in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALBERT from LYNN, MA
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Fill Cap broke off left portion in door
Used drill and easy out to remove broken part, then put in new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bernice from Estero, FL
- Parts Used:
- WD28X31818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
rusted and broken spindles
Took off little white plastic pieces at end of rail. Old rack off and new rack on. End pieces in and railing tighten with pliers. Easy!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Yorkville, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher wouldn't pump all the water out every time. And developed a small water leak.
Recieved universal parts f/ pump & mtr assy. sorted them out, picked the ones I needed to complete my repair. Installed new assy, checked operation and was completly done in about an hour.
My old bones needed a break, or I could have been done faster. All's well, and the dirty dishes are back getting cleaned via machine, and not us.
My old bones needed a break, or I could have been done faster. All's well, and the dirty dishes are back getting cleaned via machine, and not us.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from bensalem, PA
- Parts Used:
- WD21X10060
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dishwasher would not drain.
REmoved the bottom to plates on the dish washer
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.
removed the old solenoid put the new one in and
the washer was fixed. if i could replace it anyone
could do it.
Was this instruction helpful to you?
Thank you for voting!