HDB921-01 Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Traverse City, MI
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Leaking from the pump.
The part that took the longest was taking the washer out from under the counter. The fix was the easy part = 15 to 20 minutes no problems. After putting the washer back and reconecting everything,the first cycle I had some leaking around one of the two big clamps. I had to pull it out again and move the clamps around and tighten them. Much better the 2nd time around, Good to go!! HAPPY WIFE HAPPY LIFE !!!! Good Luck !!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Apache Junction, AZ
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
water leaking from housing
Piece of cake. All done and working just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Holiday Island, AR
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
motor noise.
Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Rumney, NH
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leak
Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Livermore, CA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Pump valve leaking
I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from Seattle, WA
- Parts Used:
- WD22X120
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher quit
After doing dishes by hand for four months, I decided to take a look at the dishwasher. It took about 40 minutes to identify the problem and order the part fom PartSelect. The part arrived in two days and took two minutes to install. It's best not to rush into these things.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Fort Myers, FL
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower rack had rusted through in several areas.
Pulled out the old and rolled in the replacement. The easiest part of the repair was ordering from the PartSelect website and receiving it via FedEx Ground the next day. Thank you PartSelect. Even my husband could have been successful with this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Syl from Pagosa Springs, AL
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
dishwasher would not turn on the water
took off old part, put on new part and that was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mimi from Philadelphia, PA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Old pump leaking
The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Willcox, AZ
- Parts Used:
- WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking motor seal
Followed easy instructions and completed repair in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Deming, NM
- Parts Used:
- WD22X110
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken lower spray arm hub broke,arm fell off
Remove the retaining screw in the top of the hub and install new hub in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nathan from Burlington Twp., NJ
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
leaky pump
This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from New York, NY
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing silverware basket
part came in the mail and fit the missing space perfectly. no complaints. easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Town of Tonawanda, NY
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
motor fan broke
I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!
Was this instruction helpful to you?
Thank you for voting!