HDA3500F00BB Hotpoint Dishwasher - Instructions

Since i was not sure which gasket has failed, i replaced all 4 considering the age of the dishwasher,( 2 are corner baffles ). The only time i was scratching my head was installing the gasket insert. No one mentioned to overlap or not, so i did overlap and crossed my fingers. After several cycles there is no dripping so i guess overlapping about a 1/2 inch is the way to do it. And i would suggest cleaning the gasket groove in the bottom corners really good. Good luck, bill

To remove the upper rack guide end caps, pull the inside flange gently to the rear, then twist the cap out of the track. Then the rollers come out easily, and replacing them involves merely snapping them in place over a rack frame part. Piece of cake! Roll the rack back into the guides, and replace the end caps. No tools needed!

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

Ordered the part, by using the diagram on the ge website identified the part and ordered it right them and when it came (delivered really fast) took it out of the bag and screwed it in the jet dry despenser and is working great.

Traced the problem back to the water valve. turned off the water. Disconnected the water inlet and outlet lines. removed the 2 mounting screws and unplugged the terminals.

The hardest part was removing the dishwasher from under the counter and cleaning up the large amount of water that poured out when I turned the unit on its side.
The actual pump replacement was pretty easy except there were a lot of extra parts that were only needed for other brands or other models.
I might have tightened one of the large clamps too much as there was a very slight leak after I was done. One or two drops of water per cycle, which evaporates quickly and not worth taking apart again.
It was not hard but took longer than predicted.
Much better than buying a new dishwasher or paying the estimated $350 to an appliance repair company.

Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.

The repair only required me to lift out the old unit and set the new rack into the dishwasher. I was pleased that there was nothing to put together. The rollers were already attached.
It took longer to open the shipping box than to do the installation.

A no brainer. Simply open dishwasher door, remove lower rack and set new rack in place. Roll the new lower rack in dishwasher and close door. It fit perfectly and life routine was instantly on it's way without disruption.

Rather than remove the dishwasher from the counter, I performed the repair inplace, which was much less work (although I did have to lay on the floor).
After turning off the power, I removed the two access panels at the bottom of the unit, disconnected the wiring from the pump and solenoid, loosened the drain hose fitting and drained most of the water out of the unit and into a shallow pan (the drain solenoid was stuck open, so this was pretty easy - otherwise, I still could have manually actuated the drain valve & solenoid to drain water through this hose).
There was alot of water in the unit and my pan overflowed a little. If I was doing this again, think I would have disconnected the drain hose from under the sink and drained out through that into a bucket (I could have controlled that flow better).
Once the water was out, there are just two hose clamps that hold the pump onto the unit (one on top and one in the back), and a stabilizer bar that connects the motor to the front frame. Removed these and the whole unit came right out.
The replacement pump & motor was exactly the same as the one that came out, so I didn't need any of the hose or wire adapters that came in the kit.
Reconnected the two pump connections, motor bracket and wiring, and the unit was good-to-go!

just unscrewed it from the dishwasher with my hand and put the new one back on the same way

If you are replacing an overheated solenoid that had the plastic melt, don't forgot to order a armature and link as well. I made this mistake and had to wait another week to fix the dishwasher. The repair wasn't too bad. The most time consuming part was putting the E-clip retainer ring back on the diverter shaft. Tipping the dishwasher back some really helped for me to have more room to see and work with.

Removed bottom tray from the dishwasher and in the back there is a screen with 5 hex head screws. Removed the screws and then lifted the screen out to expose the vavle. Unscrewed the valve by hand an installed the new one,hand tighten only. Reversed order for reassembly.

The top dish rack was not an exact replacement, the side shelf did not fit and the center spray did not fit. I ran into much more trouble removing the the top rack than I had thought. I used the old wheels and it finally went on but the other mentioned problems remained.

First shut off the Power and Water to Dishwasher, removed from under counter, removed sump screen and retaining clamp from sump housing and then loosened seal from inside dishwasher cavity. Upon removal I went in search of a replacement part and found Parts Select on the web, entered my model and make at there web site and found the part I needed, I could verify the size by the easy picture on a one inch tile background for the dimenision . I called in the order since I wanted overnight service, I received the part and after cleaning the area where it goes I proceded to put things back together, this took about a hour and a half and the dishwasher is back in service