HDA3640D35SA Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kelvin from Sun City West, AZ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaks
All new seals
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Arlington, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water leaking out from bottom of Dishwaser
Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Hampton, GA
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door had no resistance/no balance/would fall open
First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Chatham, NJ
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Discovered that the end caps were broken
Removed the broken items and clicked the new ones in place utilizing a pliers
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyc e L. from Prosser, WA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack kept coming off slider due to broken end
Popped in the part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Oak Hill, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
4 wheels missing from diswasher rack (lower)
removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Broomfield, CO
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rack slide end cap broke.
I put the new cap in. POC.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Everett from Lake Elsinore, CA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rack end cap was missing.
I installed the end cap by pushing the new part on to the slide rack ,right rear side
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Loving, NM
- Parts Used:
- WD26X10051
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dishwasher pump was frozen
Ordered pump mechanism and replaced defective pump. A very easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tracy from Rockland, MA
- Parts Used:
- WD12X10304
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
the top part of the dishwasher down to bottom
first i see if i could move the metal piece it wouldn't move si i used a flat head screw drive to fix it . the end piece was to long so i cut a piece off it fitting it is not moving
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Chatham, NJ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wheels colapsed
replaced new wheels
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Nashville, TN
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Several
There is nothing to tell I order send to location and their maintenance installs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacy from The Villages, FL
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap broke
The end cap took about 2 minutes to replace. I received my part quickly and installed it really quick and easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Odenton, MD
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End Cap Broken
Removal of the old end cap required pliers. Not too difficult. The new end cap simply snapped into place. Both end caps on the two rack slides replaced in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from Alexandria, VA
- Parts Used:
- WD35X21038, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lost wheel
just snapped the new part in. couldn't have been easier
Was this instruction helpful to you?
Thank you for voting!