HDA3600D35BB Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lawrence from Finksburg, MD
- Parts Used:
- WD08X10057
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
GE Dishwasher leaking
Inspected the old gasket. Removed, cleaned, re-seated existing gasket. Tested and found smaller leaks. Purchased and installed new gasket. Majority of leaks stopped but some detergent still leaks. Unsure what the problem is with that but the main leaks have been fixed. Dishwasher is less than 5 years old. Thank You.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Houston, TX
- Parts Used:
- WD28X31820
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Removing the end caps on the tracks
I gently grasped the end caps with pliers and twisted them toward the center of the dishwasher while gently pulling on them. They came out with some minor difficulty. Be careful or they can be broken. When putting the caps back on the tracks grasp them with pliers to reinsert. Use a small srewdriver to assist in getting the plastic caps to slide into place. Wear light weight gloves when doing this to avoid getting cut on the sharp edges of the tracks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from La Quinta, CA
- Parts Used:
- WD35X21038
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Rear wheels wouldn't roll, so bottom rack had to be lifted into place. Backbreaking.
The most difficult part was removing the old wheels. The plastic coating on the rack had come off, leaving the metal exposed. The wheels had rusted on - that's why they wouldn't roll. Once we got them off with pliers, hammer, screwdriver and basically everything in the tool chest, we were home free. Installing the new wheels and axles was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robyn from Spring, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the end cap for the top rack of the dishwasher broke
We simply followed the example of the end cap on the opposite side and snapped it into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Sarasota, FL
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my 78 year old aunt needed a bottom rack that was rusted and worn out
All she had to do was remove the old rack and replace with the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hermene from River Ridge, LA
- Parts Used:
- WD27X10223, WD31X10024
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Old dishwasher that came with the home I just bought
Removed the front door panel myself... pretty easy
Removed the lower panel myself... pretty easy
Tried to put new door panel & lower panel on....
had to call the x-husband to come over & do it for me! UGH!!!! HA! He is very handy and it took him a long while. Screws are not easily accessible.
But, it looks like a new dishwasher now!!! Thanks!
The moral of this story is... if you are a women... call a man to do this job!
Removed the lower panel myself... pretty easy
Tried to put new door panel & lower panel on....
had to call the x-husband to come over & do it for me! UGH!!!! HA! He is very handy and it took him a long while. Screws are not easily accessible.
But, it looks like a new dishwasher now!!! Thanks!
The moral of this story is... if you are a women... call a man to do this job!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nick from Chatham, NJ
- Parts Used:
- WD35X21038
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wheels colapsed
replaced new wheels
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlene from Nashville, TN
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Several
There is nothing to tell I order send to location and their maintenance installs
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwight from College Station, TX
- Parts Used:
- WD31X10024
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Front panel of the dishwasher was scratched badly!
I took the old front panel off which wasn't hard, and replaced with the new panel. The job would have been a lot easier if I had 2 hands, but it just took a little longer. Not much of a problem really! New panel looks great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Loving, NM
- Parts Used:
- WD26X10051
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Dishwasher pump was frozen
Ordered pump mechanism and replaced defective pump. A very easy replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Wilmington, OH
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original lower dishwasher dishrack on this portable dishwasher was so shoddy that the rubber coating on it eroded so that the metal underneath rusted and caused rust spots on the dishes and other parts of the dishrack also rusted completely through and broke off. The door on this dishwasher has
I opened the dishwasher, rolled out the defective/rusty Dishrack, removed it from the dishwasher and replaced it with the new Lower Dishwasher Dishrack.
Before attempting this repair, remember to remove any dishes from the lower Dishwasher Dishrack.
Before attempting this repair, remember to remove any dishes from the lower Dishwasher Dishrack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Odenton, MD
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End Cap Broken
Removal of the old end cap required pliers. Not too difficult. The new end cap simply snapped into place. Both end caps on the two rack slides replaced in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Oak Hill, FL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
4 wheels missing from diswasher rack (lower)
removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Arlington, TN
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water leaking out from bottom of Dishwaser
Very easy! Removed 4 screws that was holding the valve to the bracket. Placed bracket over water inlet line. Attached copper threaded coupling with pliers.Screwed valved on to the coupling. Attached bracket to the valve with 4 screws. Reattached water line. Attached bracket to frame of dishwaser. Put kickplate back on and done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Chatham, NJ
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Discovered that the end caps were broken
Removed the broken items and clicked the new ones in place utilizing a pliers
Was this instruction helpful to you?
Thank you for voting!