HDA2100V00CC Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from ANNAPOLIS, MD
- Parts Used:
- WD15X10014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Leaking Solenoid valve
1.Shut off the electric! 2.Shut off the water Supply. 3.Removed the two lower front panels(Two bolts each) . 4.The Water supply Solenoid is located far left up front . 5. Unplug power connector clip to the solenoid. 6.remove the two mounting bolts . 7. Use pliers to compress the rubber hose clamp And slide down the hose . 8 some small amount of water maybe in the hose a pan maybe necessary under the solenoid. 9.Gently pull the rubber hose off the nozzle. Complete installation in reverse. May The Force Be With You!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from WEST DEPTFORD, NJ
- Parts Used:
- WD08X10057
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door gasket was old and leaking.
I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- forrest from stuart, FL
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door gasket
from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Rockville, MO
- Parts Used:
- WD24X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Couldn't drain water
I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from PLANO, TX
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Racked rusted out
Simply removed the old rack and installed the new rack.....easy as 123 ABC. Dishwasher still works fine but the bottom rack had rusted out. Not sure if this is common for this Hotpoint dishwasher as my deciding factor to order from here was that others had the same problem as me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from JONESBOROUGH, TN
- Parts Used:
- WD28X31819
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
NEEDED TO REPLACE LOWER RACK IN DISHWASHER TO SELL HOUSE
TOOK THE RACK OUT OF THE BOX AND PLACED IT IN THE DISHWASHER, DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from HAVERHILL, MA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Leaking valve
Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from walworth, NY
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daryll from Newville, PA
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
The top drawer of the dishwasher would extend past the support rails.
The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from Davidson, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Cap had broken off the top rack, it kept sliding down
I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from WOODBURY, MN
- Parts Used:
- WD28X31819, WD28X31820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The covering over the original dishracks had worn away and the framework beneath was rusting.
The only trick was the endcaps, which were not intuitive. I followed the instructions in the following Youtube video , which direct the user to bend a tab at the rear of the endcap back away from the front using a quarter in order to allow the endcap to rotate out of position inwards into the interior of the dishwasher. The old racks then slid easily out of the dishwasher, the new ones equally easily slid in, and then the endcaps required the tab to be bent back to allow them to rotate back into position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from LAS VEGAS, NV
- Parts Used:
- WD14X10009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Broggie from Burlington, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill Cap Just Keep Turning, Not Locking In Place
I Just Open Door And Put Fill Cap In And Turn That It
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martie from FULTON, MO
- Parts Used:
- WD12X10284
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Threads on the cap broken
A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.
Was this instruction helpful to you?
Thank you for voting!