HDA3640V00SA Hotpoint Dishwasher - Instructions

First, end caps were removed from support rails to free the washer rack. This is a little tricky - flexible rear finger of cap is bent back, then rotated inboard to permit end cap to slide out. Ten top wash rack is rolled out of washer. Old roller support assembies are pried loose and then snapped off their clamp locations on the upper wash rack, one at a time. Then the new rollers are snapped on in same way, except no tools are required.
Two of the old rack rollers were clearly worn out from nearly 10 years of normal operation, where plastic shaft is a bearing surface.

took the front pieces off the front of each bar and placed the new rollers in place. Put the front cover peices back. ....that's it! The only thing i used the screwdriver for was to help remove the pieces, one was more difficult than the other.

Used a small flat head screw driver to remove the rail end covers (2) and removed the rack. Used my thumb to push the snap on roller assembly off the rack. The new rollers snap right back on the rack with just fing pressure. Re-installed the rack and then just pushed the rail end covers back on.

Very Simple Repair to a great machine. First problem in 13 years and still works great.

Removed the rack.
Removed the roller bar.
Removed the roller base from the rack.
Removed the roller from the roller bar.
Replaced in reverse order.

DONE.

The top right rail, facing the dishwasher, has a self lock tab. Using pliers, straighten the lock tab, insert the cap and then restore the lock tab to it's original position.

I just had to play around with it to attach the new cap without breaking it.....never did this before but eureka! it worked.

had to bend back the metal tab that holds the end cap on. this is tricky and a poor design from a repair point of view. i finally got the end cap off without destroying it. replacing the broken wheel was very simple and easy.

Removing the end caps on the rack's sliding arms was the hard part. It took some arm-wrestling and prying with a screwdriver to get them off. Replacing the rollers was a snap. Getting the end caps back on again was easier than removing them.

I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.

Slide it into the arm until you hear it snap

TOOK THE RACK OUT OF THE BOX AND PLACED IT IN THE DISHWASHER, DONE.

Simply removed the old rack and installed the new rack.....easy as 123 ABC. Dishwasher still works fine but the bottom rack had rusted out. Not sure if this is common for this Hotpoint dishwasher as my deciding factor to order from here was that others had the same problem as me.

I watched the video instructions and it looked easy! The old gasket just pulled right off easily! Installation of the new gaskets was quick and easy!

A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.

I Just Open Door And Put Fill Cap In And Turn That It