HDA2000T00WW Hotpoint Dishwasher - Instructions

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

Replaced with a new rinse aid fill cap.

Old baffles lift out and new ones installed - very easy

removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.

Took off old timer knob and pished new knob in to it's place.

First I opened the package and screwed the new dispenser cap into place.

Removed old rack replaced with new one which was an exact duplicate. Mama's happy; everybody's happy.

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

I removed the warped roller wheel and clipped the new one in place. Then I screwed the rail guides back on the dishwasher and guided the upper rack back onto the rail guides. Easy peasy.

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.

Removed the lower rack and installed new wheels with clips

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.