HDA400V-61BA Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Beatrice from Medford, NY
- Parts Used:
- WD18X213
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench set
Dishwasher is 5 yrs old. Never really washed right sometimes had sand on the top rack. 1 month ago started leaking from bottom put towels down and did only 1 load a day. Floor starting to rot my husband pulled out the dishwasher saw where it was leaking took the piece out saw it was cracked and repl
Unscrewed 2 screws from under the counter, pulled out dishwasher. Saw where it was leaking. Took wires loose, took the rack out, unscrew the white mesh, took out the dishwasher sump housing product saw a crack and ordered the piece. For anyone out there make sure you turn the electric power switch off before you attempt to fix anything!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mark from Fleming Island, FL
- Parts Used:
- WD7X14
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Eyelet Assembly Broke
Took off the lower faceplates. Removed the old eyelet assemblies (one broken, one not) and replaced both with new ones. Very easy to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from Sparks, NV
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Dishwasher wouldn't drain
Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clint from Quakertown, PA
- Parts Used:
- WD16X10011, WD16X313, WD16X297, WD35X10346
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Soap dispenser door wouldn't close
Replaced all ordered parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Columbia, SC
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
threads broke on rinse aid fill cap
Replaced with a new rinse aid fill cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from MARENGO, OH
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher wouldn’t start
Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Roller
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SCOTT from ROMEOVILLE, IL
- Parts Used:
- WD21X802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Dishwasher would not drain
I simply removed the front toe kick panels.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.
I DID turn the power OFF at the breaker panel prior to starting the repair.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.
I DID turn the power OFF at the breaker panel prior to starting the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from Westfield, IN
- Parts Used:
- WD24X10018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
dishwasher wouldn't drain all the way
Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Willmar, MN
- Parts Used:
- WD22X135
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher leaked at bottom of door.
I first assumed that the leak was from the door gaskets getting old (unit is near 25 years old). Therefore I replaced the door gasket and two bottom corner gaskets first (no tools needed, took about 15 minutes). All gaskets remove easily and the new door gasket "snaps" back into a groove. Pay attention to how the bottom corners of the door gasket are installed. The bottom corner gaskets simply fit back into their openings. But, leak continued. Further investigation revealed the lower offset spray arm had worn out and had a big hole in the bottom of it, which was spraying water up through the bottom lip of the door. It took about 15 minutes to replace the arm, by simply unscrewing the spray tower (reversed threads - using only my hands). Problem solved, unit cleans much better. I hope to use it a few more years until a major kitchen remodel fits my budget.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Art from Grants Pass, OR
- Parts Used:
- WD7X14
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Appliance door would fall open and was heavy to close
I first removed four screws holding the two cover panels attached to the dishwasher front at the bottom. Next I removed the broken cable and put everything back together that had sprung apart when the cable broke. Then I inserted the two door springs ends into the cable slots. Next I pulled on the springs to create slack and attached the cable / eyelet assembly to the protruding tab on the dishwasher frame. After attaching both sides the door works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebekah from NEW ORLEANS, LA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My dishwasher would not start.
I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ORLANDO, FL
- Parts Used:
- WD22X10024, WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
water would not drain
I used the website to identify a few different problem areas. I found that the motor shaft would not turn. Upon removing it, it did turn, which lead me to look at the Impeller which was worn / frozen. Ordered new impeller and installed 100 % success !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Palatine, IL
- Parts Used:
- WD19X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Leaking water pump
Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.
Was this instruction helpful to you?
Thank you for voting!