HDB727K-02 Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- BRIAN from Keller, TX
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
SOmehow the upper rack end cap went missing. I needed to replace the cap so the rack would not pull all the way out and fall down.
I used needle nose pliers. I bent the stainless steel guide arm out so that I could insert the end cap. Once the end cap was installed I used the same needle nose pliers to "pinch" the guide arm back tight around the end cap. The end cap had premanufactured "notches" to hold the end cap in place once the guide arms are pinched down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Willcox, AZ
- Parts Used:
- WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking motor seal
Followed easy instructions and completed repair in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dolores from Chicago, IL
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Upper rack slide endstop was missing.
Took seconds to pop the new stop in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Laura from New York, NY
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing silverware basket
part came in the mail and fit the missing space perfectly. no complaints. easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Cheyenne, WY
- Parts Used:
- WD12X10304, WD30X98
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Old bent Upper Rack Slide and broken End Caps
Pop off End Caps with pliers. Slide Upper Dish Rack out of dishwasher. Pop off "interior" End Caps with pliers. Slide out Upper Rack Slides. Slide in new Upper Rack Slide just past second roller guide snap on new End Caps. Slide upper dish rack back into place. Snap on new End Caps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- terry from port clinton, OH
- Parts Used:
- WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
when dishwasher was turned on no water sprayed out the rotating arm
I diconected the electric removed water line removed 2 hex head screws pulled out inlet valve squeezed the pressure clamp and pulled off water inlet line and re assembled very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Romoland, CA
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken vent on microwave
Ordered the part and installed...easy and great prices.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Loganville, GA
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bought a manufactured home
with a dishwasher. Someone had 'packed' the silverware basket and there wasn't one in my dishwasher! Ordered one from here, when it arrived, opened the box, opened the dishwasher and placed it in the correct place. Closed dishwasher - DONE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Plainfield, IL
- Parts Used:
- WD21X802
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
The dishwasher would not drain
I googled "dishwasher will not drain" and replacemed drain solenoid. The repair was relatively easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from lexington, NC
- Parts Used:
- WD15X93
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench set
Old valve had hairline crack and leaking
2 screws to remove valve, turn water off, detach water line, detach plastic water outlet line, and put the new one on, reattaching everything in reverse. Electrical hookup was just two wires to solenoid. Slipped them off and back on new valve solenoid. Some difficulty getting support screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tway from columbia, MO
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced dishwasher rack
nothing to it. slid old one out, slid new one in. however, replacement was not the same model as the original.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Stoughton, MA
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I was very disappointed in the in-the-door silverware basket most dishwashers are equipped with today and longed for the ones that have been phased out.
I went to PartSelect online and easily found an exact duplicate of my old basket at a reasonable price. I ordered it, expecting delivery in about 3 - 5 days. It was on my doorstep 2 days after the order was placed. I opened the dishwasher door, set it in the place of my choice, and what a timesaver! Try it! You'll like it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia E. from Metropolis, IL
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic Slide end cap Broke and let the upper rack come out
Put rack in place and snapped new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Muriel from Pascoag, RI
- Parts Used:
- WD21X802
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dishwasher would not drain properly
On this model the panel under the door can be removed by unscrewing two hex screws on the upper panel and two phillips head screws on the lower vent panel. The drain solenoid is located on the left side of the pump and can be accessed easily without pulling the dishwasher out from under the counter. The solenoid is held in place with two phillips head screws, and the plastic actuator that is attached to the valve stem is simply press fitted on and held in place with a retaining ring. All necessary parts are included in the repair kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Las Cruces, NM
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
End cap broke
Ordered the part from you and it was easy to replace.
Was this instruction helpful to you?
Thank you for voting!