HDA3230Z04WW Hotpoint Dishwasher - Instructions

The instructions were excellent, The repair was simple. The order process was excellent, as well as the delivertime. Part Select offers excellent bluline breakdown as well as east access to help which I did not need. Thank you Part Select for yor excellence of service.

Installed new motor and pump kit. Very easy, except that the instructions did not give any detail on the electrical hook-up. The problem was that the electrical connections for the motor and solenoid were the same on the replacement kit, making it possible to switch them. Be sure and mark the connections from the old unit before removing them.

I could not pull it out to get the new one in so I used a dremmel. Then pressed in the new one.

Thanks for your help.

Turn water off and unplug unit first. I remove the 2 retaining screws under counter, pulled out dishwasher. I laid it on it's side to get to pump, loosen up Hose clamps on inlet and outlet ports on pump. You may need a towel or rags to soak up a small amount of water from hoses and old pump. Removed the two hoses on the side, note the lowest one is the drain hose. Un plug all wire connections and loosen support bracket. Removed old pump and installed new one in reverse order. I had to use the 90* adapter hose and the white adapter for my drain hose.The kit contains all adapters and it all fits perfect. Reinstalled and tested unit worked great!!!

Took off little white plastic pieces at end of rail. Old rack off and new rack on. End pieces in and railing tighten with pliers. Easy!!!

pulled out old motor. replaced new motor. works like new.

i couldent use the hole unit because it was for a dryer.

i new the motor would work because it had the same gear and rpm. i couldent find a motor no wear.

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

Identified solinoid responsible for the operation of the drain flapper valve had become damaged, possibly due to its coil shorting and overheating, the inside plastic insulation then melted and came up through the solinoid pin hole. I removed the tension spring holding the flapper drain valve shut, removed the eclip holding the white phenelic arm connected to the tension spring, removed the two screws mounting the solinoid assy. I threw out the bad solinoid. I then proceeded to install the replacement solinoid in reverse order of removal. The end. Works like a champ ! Thank you for your quick shipping response time. My wife is now once again happy. As you know, if my wife isnt happy, I sure wont be happy. :)

Removed the 6 screws and took off the inside pannel. Removed 2 screws that secured the timer.Unplugged old timer leads and put the new one in reverse sequence. Piece of cake.

1. Installed temporary plywood cover to prevent new puppy from wandering under dishwasher.
2. Ordered new toe kick; arrived in two days.
3. Unscrewed plywood.
4. Installed new toe kick with original screws.
5. Crossed project off to-do list.

Opened package, removed cap and screwed it in place.

Unscrewed unit from counter and loosened legs using adjustable supports under dishwasher. After switching off water under sink and power at circuit breaker, removed motor and pump assembly and replaced with repair kit.

Turned off the electricity to the dishwasher,removed the old solenoid,and put the new one on(very easy),turned the electrical breaker back on.

Used drill and easy out to remove broken part, then put in new one

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .