HDA1100N00WH Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sally from Wauconda, IL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of the wheels and hangers went missing.
Check website, order part. Hardest part was determining which was the right part. Needed the axle--I call it the hanger. I had previously called and ordered, but only received the wheel with no way to attach it. Push the axle into the wheel. Push the axle onto the rack. Since it was new, it didn't slip right on, and had to push it hard. (However, when it snapped on, three of the other wheels and axles came off.) Had to put them back on as well. Much easier, as they were older and not as snug. Total time: Took longer to open the package than put it on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Corvallis, OR
- Parts Used:
- WD12X10284
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Old rinse aid fill cap broke off at base
I removed the broken stub of the old fill cap with a screw remover. This was the only part that wasn't easy. The new cap fit fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Fort Worth, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
miss wheels
It was amazingly easy repair. I just order the correct parts from “PartSelect” and installed them and done. It was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Riverview, FL
- Parts Used:
- WD21X10261
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The unit would not start.
First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi from North Las Vegas, NV
- Parts Used:
- WD02X25492
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Right door spring broke
Took lower panel off with screwdriver. Removed old spring. Attached new spring. Very easy, and I'm a woman. LOL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carole from Libertyville, IL
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken lower wheel ion lower dishwasher rack
Pieces just snapped together. Simple an quick. Part select was wonderful in assisting.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deanna from Benton Harbor, MI
- Parts Used:
- WD22X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Extendable tower broke
On the front ,lower side of sprayer arm removed the 1/4" screw and you have to stick your head inside and look on the backside of the spayed arm. Locate the plastic clip and gently pry a little just enough to loosen it off the rest of the way, be careful not to break off. It came right off I popped on the new one replaced screw and rain a load of dishes. Thanks for your help and great products for us do it yourselfers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth R from Marcellus, MI
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Fractured brass bezel on bottom of valve- Leaking
simply removed broken valve and replaced with new valve, easy peasy. shipping was GREAT, Overnight. all in all a easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Oronogo, MO
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
existing gasket dry rotted
This repoair was needed due to diswasher leaking out of side door. I just moved in about 6 months ago and needed to use dishwasher. When it leaked i noticed it was in need of a gasket. I searched the internet and came accross "part select". Part showed up in less than 3 days and was a breeze to install. The original gasket came out just by pulling, cleaned up channel and installed new gasket.slid in real easy. I did take off inner door panel to inspect for any damage. none noted. Perfect fit first time. Dont get confused folks if the part has another name as some parts are interchangeable in the industry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from petaluma, CA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable), Wrench set
water dripping near front left of dishwasher
look at neww part first then r&r
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert j from elpaso, TX
- Parts Used:
- WD21X10261, WD13X10003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
dishwasher stopped working
knew the cause of problem ordered parts prompt delivery 16 yr grandson did the repair with little or no assistance
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Wantage, NJ
- Parts Used:
- WD15X10014
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
dishwasher was not filling with water
very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Monterey, CA
- Parts Used:
- WD15X10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Water leaking on floor
Water was leaking from under refer next to installed under counter dishwasher. Once determined to be dishwasher not refer I removed dishwasher toe place was able to see dripping inlet solenoid valve. I had to disconnect 11V power, shut off inlet water, disconnect inlet water house and remove dishwasher from under counter. Once dishwasher was in center of kitchen I flipped it upside down and removed the electric solenoid inlet valve. Removing the valve took one wrench to remove inlet hose then two wrenches to remove 90 degree brass fitting and another to hold solenoid. I used a nut drive to remove two screws that released the solenoid from the dishwasher frame. I used teflon tape to reattached the 90 degree brass fitting and inlet hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hoyt from Pleasanton, TX
- Parts Used:
- WD18X10039
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher was not draining.
Attached is a link to a great youtube video, that shows the exact steps to take to do this job. I just follow the instructions and the repair was flawless.
Was this instruction helpful to you?
Thank you for voting!