HDA3640N10SA Hotpoint Dishwasher - Instructions

Removed the wire clip, then removed two screws on mounting bracket. Then disconected the hose. Removed the brass elbow.

Then reversed these steps and I was done.

Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip. , Rescrewed in the new rubber connector. ( Hint- used petrolem vasaline on the rubber connector base for a water tight fit) . Reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. Turned water back on. All worked at well.

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order

Took the screws out of the back of the doorl located the switch and replaced it put screws back in and it was fixed

Replaced with a new rinse aid fill cap.

replaced solenoid. worked properly after repair

I removed drain hose to install 1 yr old dishwasher. Installed it fd water leak at drain hose. Removed it, found collection chamber was collapsed. This was a factory bo-bo. Collection chamber is made of p. V. C. I also had a problem with the sump filter ball. Called g. E. The told me to just put the ball in the chamber,not, the ball has to come in from the top, removing the spray arm,sump cover,major disassembly. Now I know how to completely dismantle a dishwasher. Home depot had no idea what I was talking about???now works great!!!!!!!!!!!!!!!

Just lift out the old dishrack and put in the new. Very easy and straightforward. Easy to order, unit came assembled. Happy customer.

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.

removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!

Old baffles lift out and new ones installed - very easy

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.