HDA2030Z02WW Hotpoint Dishwasher - Instructions

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

replaced the master toner relay.

I had to readjust the door latch to get the door to close

This was really easy. The parts fit perfectly. First i turn off power at circuit panel; turn off water and dissconnected water line and discharge hose. Removed dishwasher from under counter and placed on side. Disconnected connections to motor and pump and replaced and installed same as one unit.

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

Followed easy instructions and completed repair in less than 30 minutes.

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

Removed dish washer from cabinet area and snapped new clip into cable and hook into support.. The time that took the longest was to removed the screws to pull the unit out of the cabinet area.. Very easy fix...

Dishwasher had become noisier & noisier in last year during wash & rinse cycles. After looking at various web sites, decided to first pull motor/pump & try cleaning it out. That made no difference. Also looked for anything loose that could cause vibration. No change in operation. Decided to go for replacing motor/pump & found Part Select had best price. Part came next day! I was amazed! Looked at video, then removed old unit and attached new one. Easy because it was exactly same connections. Ran dishwasher and it sounded 100% quieter - like when new! Very happy!!

Removed old gasket, cleaned grooves, installed new gasket

Removed old gasket. Then cleaned the track with a strong paper towel soaked in Windex to remove accumulated scale/soap. Followed the instructions provided with the gasket. I did not need to remove any screws from the door nor did I need to tumble the gasket in a dryer to remove kinks (There really were no kinks in the gasket, as supplied.). I did use a mirror to locate where the gasket should go underneath the bottom of the door, which you can't see. Feeling for the track with your fingers was sufficient for the installation.

I removed the old cap and put on the new cap.

followed the excellent instructions accompanying the gasket.