HDA3420Z00BB Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sandra from Rumney, NH
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Leak
Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Livermore, CA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Pump valve leaking
I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Hughes Springs, TX
- Parts Used:
- WD28X10232
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken tower
removed old tower uuing a screwdriver to losen the tower from rack and slid the new part into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lakeport, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
cracked riser in spray arm
Ordered part Monday evening installed it on Wednesday afternoon. Required a pair of pump pliers to loosen old part, new part screwed in by hand. No leaks, no problems. Took longer to explain what caused the problem then it did to fix it. I explained to the owner that overloading the dishwasher was most likely the cause. Dishes can move or fall against the riser during wash, preventing it from dropping back down. Pulling the lower rack out with the riser bound up caused the part to crack. Thanks for the speedy delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Chantilly, VA
- Parts Used:
- WD28X31820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace upper rack in dishwasher
Remove end caps on the slides on the upper rack pulled old rack out put new rack in push end caps back in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Hubbard, TX
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
would not clean the dishes
I unscrewed the lower spray arm and support assembly and then screwed the new part in. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anton from Middletown, CT
- Parts Used:
- WD28X31820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
how to remove rack
go to google..replace ge dishwasher rack.. very clear way to pry tab with a quarter and rotate end cap.. remove/replace rack reverse install end cap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Yucca Valley, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The smallest portion of the sprayer had been broken
Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merwyn from Lima, OH
- Parts Used:
- WD28X10007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
tower cap broke
simply snap new one in place. I will have to say your service was fantastic. I received the new cap 2nd day. I am very pleased and would not hesitate to order something else if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loring from Cambridge, MA
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket deteriorated
followed the excellent instructions accompanying the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Mt. Pleasant, MI
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tower Broken
Order new part. Lightning fast delivery. Unscrew old one, put in new. 30 seconds. Don't get any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Mesa, AZ
- Parts Used:
- WD08X10016
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking gasket
Removed old gasket, cleaned grooves, installed new gasket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burl from Spring Valley, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Motor failure because of black power wire separation.
Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Town of Tonawanda, NY
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
motor fan broke
I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mimi from Philadelphia, PA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Old pump leaking
The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation
Was this instruction helpful to you?
Thank you for voting!