HDA1000Z01WH Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Russell from Columbia, SC
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
threads broke on rinse aid fill cap
Replaced with a new rinse aid fill cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clint from Quakertown, PA
- Parts Used:
- WD16X10011, WD16X313, WD16X297, WD35X10346
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Soap dispenser door wouldn't close
Replaced all ordered parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Richardson, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Roller
I watched the video and did exactly what he did. I am a novice when it comes to repairs. I learn as I go. This repair went flawlessly. Ordering was quick and easy. The part arrived quickly. The repair took less time than expected. The part was what I needed and nothing else broke or went wrong when repairing the original problem. It was a 100% success.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elaine from Oceanside, CA
- Parts Used:
- WD28X31819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rusted/corroded lower dishwasher basket
removed old drawer-like basket, installed the new duplicate replacement part. Easiest "repair" I've ever done!
Was this instruction helpful to you?
Thank you for voting!
water leak due to bad rubber connector
Ordered rubber connector and it arrived the next day. Shut off main power and water. Disconnected water supply and pulled unit out from under counter. Flipped unit over on it's side. Disconnected wiring, drain hose, clamps and completely removed motor/pump. Rubber connector would not unscrew by hand so I found a drinking glass slightly smaller in diameter than the connector inner diameter. Inserted glass in connector and proceeded to unscrew connector by turning connector and glass together. After removing old connector I cleaned the mating part after removing it from inside the washer and removed all the build-up. Replaced everything back in same order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SCOTT from ROMEOVILLE, IL
- Parts Used:
- WD21X802
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Dishwasher would not drain
I simply removed the front toe kick panels.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.
I DID turn the power OFF at the breaker panel prior to starting the repair.
The solonoid is staring you in the face.
I removed the small nuts on back side of the solonoid bracket and removed the retaining clip and springs.
I installed the new solonoid and was very surprised how easy it was.
I DID turn the power OFF at the breaker panel prior to starting the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebekah from NEW ORLEANS, LA
- Parts Used:
- WD21X10261
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My dishwasher would not start.
I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Palatine, IL
- Parts Used:
- WD19X10032
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Leaking water pump
Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian M. from Hereford, AZ
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Not Draining, Leaking
Unplugged unit, unscrewed screws on top of dishwasher attached to countertop, undid water supply and drain hose that goes into tee with garbage disposal. Using crescent wrench turned front leveling screws up all the way and slid/rocked dishwasher out from under the counter - I had no problem leaving back leveling screws down. Turned dishwasher over on some towels (it WILL leak some water so spread out some towels!) so it was oriented like the directions that came with pump and motor. The directions were good, although color or a picture might have been more helpful. CHECK the new pump/ motor unit CAREFULLY for any loose debris from packing etc. I had a small piece of plastic that was in the top of the motor that goes in the dishwasher bottom that rattled around after I installed everything and put it back. I was able to get to it from the drain assembly in the tub but it made a heck of a racket at first. All in all, I had a great experience. I'm glad I ordered the pump and motor even though I only thought I needed the drain solenoid because when I took the old unit out, the prop on the old impeller was almost gone. Easy to order, good customer service (I called with a question and talked to a wonderful customer service representative!), good directions and easy to do. I'd say a 4 out of 10 in terms of difficulty. Thanks PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from UPPR CHICHSTR, PA
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Wheel had melted and support cracked
Removed the lower rack and installed new wheels with clips
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from ROLESVILLE, NC
- Parts Used:
- WD21X10261
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
dishwasher did not start
Took out interlock switch (two leads) and replaced with new one. As simple as that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Asok from HELOTES, TX
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Three of the 8 wheels broke.
The newly purchased wheels have a little different design and could be installed in a matter of few seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Clifton, NJ
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dispenser cap would not stay in place because it had melted
First I opened the package and screwed the new dispenser cap into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kim from Wilmington, OH
- Parts Used:
- WD21X652
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Would not pump in or out.
With no wiring diagram, I was reduced to testing each component discreetly. The "Heated Dry - On/Off" rocker switch tested open in both switch positions. Replacement of it corrected the problem. I'd still love to see a wiring diagram to learn just where (and maybe why) in the circuit that silly switch interrupts current to the fill and pump-out solenoids. I would not recommend this repair without a wiring diagram for anyone unfamiliar with basic electricity and motor, solenoid, etc. operation.
Was this instruction helpful to you?
Thank you for voting!