HDA2100H65BB Hotpoint Dishwasher - Instructions

got the new one and slid it right in

unplugged old switch and installed new one. it took 5 minutes to do. 20.00 saved me 400.00 on a new washer.

ordered,received,opened box,took old rack out,put in newrack perfect!!!

Switch off the circuit breaker supplying power to the dishwasher.

Remove the 6 screws that hold the plastic face of the inside of the dishwasher door, and lift out the inside liner. This may be a good time to wash it down, as it is probably a little messy. It may also be a good idea to put something a little heavy onto the door to keep it laying in the open position as the springs will keep lifting it back up.

Remove the screw holding the spring device down over the interlock switches and the thin plastic cover and put aside ready for re-installing again later. The spring may have flattened a bit and it may be a good idea to bend the end open, just a little, to give it back some tension. This is the spring that activates the interlock switches when you latch the door.

Unclip the faulty Interlock Switch by pushing (with your fingers) the little plastic clip holding it in and lifting it out of its cradle. If the switch to be replaced is the one furthest from the machine (or nearest the top of the door) you will have to take the bottom one out first so that the clip can be released.

Using small pliers pull the electric connectors off the faulty switch and reconnect to the new switch in the same way that the faulty one was wired.

Snap the switch (or switches) back into place in the cradle.

Replace the spring activator along with the plastic sheeting and screw that back in.

Put the inside of the now clean door back down into place, making sure the on/off lever is inserted through the slot in the front of the door, and that the piece of Styrofoam is inserted back into position.

Screw the screws back in, starting with the one at the top center nearest the on/off lever and then work your way down the sides from top to bottom.

Switch the circuit breaker back on and give it a whirl. Enjoy!

First I turned off the breaker to the dishwasher. I then removed the bolts that held on the inner cover(note the two small bolts go on the bottom one on each side). I lifted the switch up and disconnected the wire clips from each side. I then put the new switch in place with the wires attached. Then replaced the cover and screwed it into place. Closed the door and flipped the breaker back on and turned the dish washer on and it started up. A very easy replaceable part.

My son took the part and it plop right into place with a click, and we were able to use are dishwasher again,Thanks

just lifted out the old one & replaced it with the new one. Couldn't have been easier.

Removed the old rack and slid in the new rack.

big project remove old dish rack and replace with mew rack.

The part arrived in three days and matched perfectly. All I had to do was take out the old rack and set the new one on the track and close the door. We recently sold our house and want to leave everything clean and in good shape just as we would expect it to be. I wish replacing all parts was this easy. Bonnie Stanley

door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.

i first order the corner baffles and put them in. no change at all, still leaked terribly. the old baffles looked pretty good so i kept them. i then ordered the door gasket and the insert. i removed the old one, put in the new, and still no change. i thought perhaps the machine hadn't been used at all because it was like brand new inside, and previously owned by 'a little old lady'. i decided to load it up and run it on a regular wash, and have done that three times now. it drips a very small amount on the left corner but i'm quite happy that it decreased so much. I think perhaps the seal might be setting with the heat of the cycle because each time a load goes through it get less and less drips from that corner. The first order was sent by ups and they couldn't find where i lived so i actually had to go pick them up, but the second order was sent fedex and they had no problem finding my home, and i was very pleased with how fast my order came.

Held panel in place and drilled holes and installed drill screws.

Put part in. Put the door cover on & turned on & it worked. Thanks for having the part. So far, so good.

Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.