GSD1200--01 Hotpoint Dishwasher - Instructions

Basically, I told my girlfriend, hey, if you are board, this box has the parts to fix the dishwasher in it. When I got home from work, I had to connect one wire, and tighten a couple of screws. The kit has great, easy to follow directions. Thanks!!

Pull the old Door Gasket out.
Then figure out, how the new one should fit in the door.
Push the new one softly in, and the repair was perfect done.

Recieved universal parts f/ pump & mtr assy. sorted them out, picked the ones I needed to complete my repair. Installed new assy, checked operation and was completly done in about an hour.

My old bones needed a break, or I could have been done faster. All's well, and the dirty dishes are back getting cleaned via machine, and not us.

Not really difficult to do. First remove the washer from the counter and flip it over. Carefully determine the correct drawing in the instructions which matches your machine. Follow insructions and double check everything. Took about an hour - and I saved about $350.00 by fixing it myself rather than buying a new one!

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

The part that took the longest was taking the washer out from under the counter. The fix was the easy part = 15 to 20 minutes no problems. After putting the washer back and reconecting everything,the first cycle I had some leaking around one of the two big clamps. I had to pull it out again and move the clamps around and tighten them. Much better the 2nd time around, Good to go!! HAPPY WIFE HAPPY LIFE !!!! Good Luck !!

Turned off breaker. Turned off water and disconnected water line to make it easy to pull unit out and turn on it's side. Once that was done it was an easy swap out. Exact same motor/pump assembly. Love this site. Thanks

pulled washer out and turned it upside down to get to the pump&motor.
no problem to fix

Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.

Piece of cake. All done and working just fine.

Originally replaced solenoid without pulling unit out, but continued to leak. Purchased the entire motor and pump kit; pulled unit out, turned it on end and replaced the motor. The only problem was that no new ground screw was sent with the kit and the existing screw wasn't quite short enough to connect. Either the hole on the replacement kit needs to be deeper or a bond screw needs to be sent that will fit the new kit. We had to find our own screw that would fit properly.

followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.

Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.