HDA460-01 Hotpoint Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brent from Fort Collins, CO
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dishwasher was making lots of noise, and specifically rattling
The repair went really smoothly, I found a video on youtube for how to remove the dishwasher, and the video on the parts page did a great job covering replacing the motor. The repair went really well. As others have noted, it ran really nosily the 1st time, and a little the 2nd. After that, it ran quieter, and stronger than it has in the 4 years we have owned the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ben from Nashville, TN
- Parts Used:
- WD26X10013
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
replace pump motor assembly
Too easy- what made it easier was this is a portable roll-around unit I could lay on it's back. Loosen the two clamps around the washer pump, hook up the drain solenoid, washer motor wires, attach the motor hanger, that's basically it. It took longer to make sure I was working from the right set of instructions- this pump covers several models. Once I had that right, it was really a snap. Now the unit is so quiet. It once sounded like a jet engine in the kitchen, now it runs so quiet you can hear the water splashing around inside- a big improvement. We should be able to hang onto this thing for a while longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Burns, OR
- Parts Used:
- WD26X10013, WD15X93
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
dishes not getting clean
I watched and read what other people did with the same problem and bought the part they did and installed the part which was real easy and the dishwasher works great.thank you to everyone that left information.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from kirtland, OH
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Water remained in dishwasher after cycle.
Dishwasher is 22 years old and I'm 80 years old so it took longer, about 3 hours. After removing, turned upside down and removed old pump-motor assembly and replaced with new following directions [which took a little while to figure out; my assembly was quite a bit different from the replacement pump-motor]. Pleasantly surprised at how quiet the dishwasher now runs. Normally I would replace this old an appliance, but this unit has provision for inserting a wood panel that blends with the cabinets and a new GE dishwasher with this feature costs $1300 MSRP. I'm trying to save money for when I get old so I decided to do the repair myself. For $150 it was a worthwhile investment.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chuck from Austin, TX
- Parts Used:
- WD26X10013
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Leaking water
Most difficult part of repair was getting dishwasher out and in under the cabinet. Especially, feeding the copper water line from under the sink and then back while trying to align the connection. Installing the part itself was easy with good instruction for taking it off and reinstalling. However, since the motor had been upgraded, it required new connections. The connections were provided for this, but no instructions for the electrical connections.
Was this instruction helpful to you?
Thank you for voting!