HDA312-03 Hotpoint Dishwasher - Instructions

followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.

Turned off breaker. Turned off water and disconnected water line to make it easy to pull unit out and turn on it's side. Once that was done it was an easy swap out. Exact same motor/pump assembly. Love this site. Thanks

pulled washer out and turned it upside down to get to the pump&motor.
no problem to fix

Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.

Piece of cake. All done and working just fine.

The part that took the longest was taking the washer out from under the counter. The fix was the easy part = 15 to 20 minutes no problems. After putting the washer back and reconecting everything,the first cycle I had some leaking around one of the two big clamps. I had to pull it out again and move the clamps around and tighten them. Much better the 2nd time around, Good to go!! HAPPY WIFE HAPPY LIFE !!!! Good Luck !!

No story just locate partselect.com on internet, select part and order. Part received in a timely manner in great condition. Thanks

Originally replaced solenoid without pulling unit out, but continued to leak. Purchased the entire motor and pump kit; pulled unit out, turned it on end and replaced the motor. The only problem was that no new ground screw was sent with the kit and the existing screw wasn't quite short enough to connect. Either the hole on the replacement kit needs to be deeper or a bond screw needs to be sent that will fit the new kit. We had to find our own screw that would fit properly.

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

nothing to it. slid old one out, slid new one in. however, replacement was not the same model as the original.

Original part no longer made. Substitute too small by a half an inch. Corrected the problem by removing the 4 corner wheels from the old rack and put them on the new one. Now, it fits and works perfectly.

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!