GDB755RJB1 Gibson Dishwasher - Instructions

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.

New one snaps into place easily.

First I disconnected the dishwasher, then I disconnected the drain hose. I pulled the machine from under the counter and turned it on its side, so that I could see where the drain pump was. I removed the two screws that hold the element in place. I then pulled the pump out and disconnected the two wires. I took a good look where each wire was attached. I also had to disconnect the pump from two small hoses. I installed the new pump, I had ordered from PartSelect, following the reverse procedure. I reconnected the dishwasher and slided back under the counter. I confess I didn't believe it would work. I was prepared for failure. The machine started, then when the cycle changed, I heard the water draining into the waist pipe under the sink. New hot water filled the machine. Would this water be drained out and at the end, after the rinsing cycle, would the dishwasher be empty and completely free of water? I waited for the end of the rinsing, then I opened the door and checked for any water left at the bottom. Suddenly a feeling of joy and pride went through me. All water had been drained out by the new pump. I had repaired my dishwasher. I didn't have to throw this handsome and well made machine into the street. My kitchen sink was no longer full of glasses and dishes. I was washing all I had accumulated during the week. My kitchen became clean and organized just like before. At this point I took an oath: when my dishwasher would break down next time, I would repair it , even if its motor, the most expensive part, had to be replaced. I was going to do it with the help of the experts at PartSelect. Thanks guys for your help and for inspiring confidence in myself. I DID IT! What a great feeling!
Now I understand the feeling a doctor must experience when he brings back to life a dying patient.

Turned off power to dishwasher.Used a screw driver to rermoved the outer top of door.Used star wrench to remove door latch.Repalced wire for wire on door latch.Reinstalled door latch with star wrench.Reinstalled outer top of door with screw driver.Turned power on.Tryed door lath.Operation is Ok.Ran dish washer.No leaks.Operation is OK.

Water had been dripping for quite some time causing the floor boards to warp and buckle causing the door to no longer align. Water drip could be seen coming from the motor area. Ordered the O rings and replaced. Get Motor & Pump schematic Pub to visualize how parts fit together. I recommend getting motor (~$90)which comes with O rings (~$50 for O rings alone) because, as it turns out, the leak was in motor. I will post repair process in separate posting.

Remove 3 screws from stem assembly. Swapped the old for the new, replace screws. Installed and lock lower wash wand. Fixed in 5 min. Great service and prices. My wife thanks you. (Had to hand wash dishes for a few days) thanks

Removed 6 screws, pulled the front cover forward, removed the old door latch, installed the new latch, replaced the screws, DONE! Took about 10 minutes. The new door latch works to open and close the door, and the dishwasher runs fine when the door is closed. However, the new door latch does not lock the door into place like the old one did. I didn't remove the screws and loor latch assembly again, but there must be a difference between the old part or the new part. And I noticed that the old part number and the part number of the replacement part are not the same, although the website indicated that it was the correct part for my model.

Our dishwasher sat in a warehouse for a year after our move from CA to TX. When I finally installed it, there was some sort of white mineral deposit that had built up on the heater element. I didn't notice it back in CA. I tried to get as much as possible off but it kept building. So I purchased a new heater element. It's been in for a few weeks and my wife thinks the build up is happening again.
To Repair;
Unscrew the dishwasher from the counter. They'll be one or two screws attaching the dishwasher on the underside of the counter.
Pull the washer out carefully.
Remove any dishes and the bottom rack.
Tilt washer on it's side.
Remove wire connections to heater element (They slide right off but make sure to remember which one goes where)
Unscrew the nuts that are holding the element on. I used some pliers. It wasn't difficult.
Remove old element and replace with new.
Reverse order.

Much easier than I expected. The bottom of the door gasket simply pulled out and the new one slid back into the same spot without any issues. That gasket did not solve the problem. The unit continued to leak. We waited for the back ordered door gasket approximately 2 week to come in. Once it came in the process took about 10 minutes. The old gasket easily pulled out of it's groove around the door. That gasket was dried out and worn in several places. We fitted the new gasket in the groove, trimmed off the excess, closed the door and ran the dishwasher and had no leaks. The two gaskets definitely did the trick. This is an easy DIY for anyone and the parts were priced right!!

Removed the 4 screws that held the dishwasher in place, tilted it out, removed 2 nut screws on striker, installed new striker and put it back together. Very simple.

Thank you for stocking the parts and shipping them as promised.

I'm a stay-at-home mom of 3 kids, so I enlisted the help of my oldest son (5 years old) for this job while the 2 little ones were asleep! First we cut the power to the dishwasher, then we removed the 2 bottom screws on the stainless steel front and slid it off to expose the back of the dispenser. We removed the red and white wires from the left side of the dispenser, took out the 6 screws holding the dispenser in place, put in the new dispenser, hooked up the red and white wires (in the right order), and flipped the breaker back on! We ran a cycle to make sure it worked, and it did!! My husband was thrilled! He thought for sure we needed a new dishwasher! :o) Thank you, PartSelect!

DO NOT BE TEMPTED TO REMOVE THE INNER DOOR SCREWS!!!!! I was and added about 10 minutes to a repair that should take less than 5. The lower door gasket just pulls out the bottom of the door. No tools required, just pull it out. The new one just pushes in, no click or anything, just make sure it bottoms into the groove.

After having a repairman out to changing the door handle and seeing how easy it was...I decided to try to fix the spring issue myself. I am fairly confident with most small fix it items in our house, so decided to order the original spring & linkage. The website was pretty self-explanatory, but wished someone hinted that when you have one broken spring, the other usually goes out within a short period of time. Note to others, ordered 2 springs & linkage and avoided another shipping charge. Do both springs at the same time, and will save you time in the long run. Otherwise, super easy to change out...wish all appliance issues were this easy to fix. I did not need to take of door off....I just needed to lay on floor & become a little limber. Other than that...super easy.

Removed the bottom covering on dishwasher and then ran it to figure out where the leak was coming from. Noticed it was dripping off hose, but not actually leaking from hose.

Unplugged dishwasher and slid it out from cabinet area (be sure to turn off and disconnect water supply)

Followed delivery tube up side of dishwasher to top of tub and noticed reminents of where water ran down side of tub.

Loosened delivery tube by plastic nut inside of tube and removed. Noticed gasket was partially depleted.

Ordered new gasket, replaced and put everything back together. (Be sure to use teflon tape on water source fitting and tighten firmly). No leaks