GSD3420Z02BB General Electric Dishwasher - Instructions

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

I pulled the two clips in the rack guides and pulled out rack and reinstalled the new rack and put the clip back in the rack guides

Thanks for your prompt shipment of the rack I ordered

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

After researching for a few minutes on this site I was pretty confident that the problem I was having was a faulty check valve. I removed the 4 screws holding the cover in place at the back of the dishwasher tub, twisted out the check valve and saw it was obviously shot. I ordered the correct part and 2 days later I had the dishwasher working like new. Installation was a simple as could be....twist in the new valve and reinstall the 4 screws.

Partselect was the only one that had the correct solution. The Piston and Nut assembly fix the problem. The washer on top of the piston was worn and it would not fully close. Replace the piston and nut assembly within 15 minutes after I found it.Shipping was supposed to be within 3 days. The part came the next business day during the thanksgiving holiday. WOW

The part that took the longest was taking the washer out from under the counter. The fix was the easy part = 15 to 20 minutes no problems. After putting the washer back and reconecting everything,the first cycle I had some leaking around one of the two big clamps. I had to pull it out again and move the clamps around and tighten them. Much better the 2nd time around, Good to go!! HAPPY WIFE HAPPY LIFE !!!! Good Luck !!

first I removed the screen in the back of dishwasher and then I replaced the check valve

Removed the 4 1/4" screws holding the rear screen to the bottom of the inside of dishwasher. "Piston & Nut" assembly was badly corroded- to the point that no dirty water was leaving the dishwasher. Because the appliance is at least 10 yrs old and there was nothing happening during the rinse cycle, I initially assumed the worst- that the pump was bad. After reading the other descriptions of the problem here, I said, "what the hell?, if a $20 part fixes it, I'll be amazed- if not, I'm out $20 and looking at another $300 for a new dishwasher!" The $20 part (inc. shipping) did the trick. Thank you, and your website is on my "highly recommended" list! One note- the piston & nut assembly did offer some resistance as you might expect after being "gunked" in place for 10 years. However, the top has some lugs or ears built into it, so a few taps with a hammer on my largest straight-blade screwdriver loosened it right up...

Looked online for a general cause. ABout 60 to 80 percent, the cause was the piston and nut assembly located in the back of the dishwasher. Ordered the part and installed in nothing flat. Only four nut screws to remove the take the filter off and unscrew the piston and nut assembly. Next cycle, no water and the drying cycle seemed to be better. Guess because no water in the bottom of the dishwasher. Good input and fast turn around on the part.

Remove the screen that runs along the back of the dishwasher.In the middle of the area that was covered with the screen you will see a white plastic valve with 2 little ears sticking up. Use the nose of a pair of pliers to twist counter/clockwise on the valve and it will come right out. Inspect the valve.If the rubber cone shaped valve inside the valve can be pushed through the top of the valve ,the valve is bad.Replace it and go wash your dishes.

Once I found out where the pison was it was easy. I removed the far back screen that runs across the entire back of the inside of the dishwasher. There was four screws to remove this screen. This exposed the Piston assemply which is threaded, so you just twist it off like a big nut. It was easy to tell that the rubber on the piston was not sealing and needed to be replaced.

i unscrewed the 4 screws in the back, took off the guard thing, and unscrewed the existing part with my hand. put new part in and ran dishwasher. the part did not fix the problem, now i'm on to maybe replacing solenoid? i have no idea. this part was simple to replace though. hope i can fix this issue, i need my dishwasher to run right!

remove the four screws in the back of dishwasher on the inside. Remove screen. Remove the piston nut assembly for the check valve. Re-install the screen and four nuts and your done.

I put on my rubber gloves, removed the lower wash rack, removed four screws from the drain guard. I unscrewed the defective part, installed the new assembly and hand tightened. Replaced the cover and installed the screws removed earlier. Re installed the lower tray, and ran the rinse and drain cycle. It has been working beautifully ever since.

After running a test cycle and realizing the pump was working but not pumping all the water out, I checked the troubleshooting guide and parts list.
I found there was a check valve at the back of the machine and when I removed it I saw it was split causing the water to return into the unit. I ordered and replaced the check valve and the unit is back in perfect operation.