GSD3910C02AA General Electric Dishwasher - Instructions

I pulled the two clips in the rack guides and pulled out rack and reinstalled the new rack and put the clip back in the rack guides

Thanks for your prompt shipment of the rack I ordered

replaced pump and motor with new one. worked but pump would not empty the water. ordered additional parts check valve,seal and box that check valve screwed into. did not fix problem. Got to looking at replacement pump and discovered thet discharge solonoid was not completely opening the discharge port. I could hold it down manually and the machine would empty. I reported the problem to parts select and they without question shipped me a new pump and motor. took the dishwasher out of the wall again and swapped them out, and now it works fine. the repair was easy and simple. the difficulty was taking the dishwasher out and reinstalling it 3 times. I will use parts select again if the need arises.

took the moter off and the impellar off replaced the impeller .back and turn the washer back on but it still wouldnt .wash .the moter wouldnt turn .so had the moter tested and it was the moter . found out how and what to look for on you tube .it was a big help in how to fix your washer .typed in model and what kind portable .it was easy .thank you for haveing my part also .and shipping was real fast .

Pulled the dishwasher out from under the counter using a little rug to keep the metal feet from scratching the tile. It is surprisingly light. Old motor and pump are held in mainly by pipe clamps, easy to remove once the washer has been pulled out and turned on its side.

The instructions that came with the pump kit show how to set it up for several different dishwashers. Once you figure out which one you have it is quite easy to set it up. Mine leaked when I first started it up. I pulled it back out and re-tightened the large pipe clamps and it now runs dry.

The dishwasher runs quieter and the dishes come out clean now.

First, remove the bottom front covers (two parts four screws). Second, remove the two screws at the top that secure the dishwasher to the counter. Third, gently pull away the dishwasher from underneath the counter just far enough to see and be able to remove the door spring(s) - one on each side. Fourth, remove the existing hinge arm link(s) if not already broken off, replace with the new one(s). Note that the door hinge goes on the door (front) side of the spring and the other side fits into a groove on the door arm - the other end of the spring attaches to one of the 3 available holes on the frame at the bottom. It would be a good idea to replace the hinge arm links on both sides even if only one is broken. Make sure that the door has the right tension (each spring can be hooked in 1 of 3 holes to adjust the tension). Then gently push the dishwasher back under the counter. Finally, replace the screws under the counter and replace the covers on the bottom front. All of this should take no more than 15-20 minutes. This was an easy job!

I put on my rubber gloves, removed the lower wash rack, removed four screws from the drain guard. I unscrewed the defective part, installed the new assembly and hand tightened. Replaced the cover and installed the screws removed earlier. Re installed the lower tray, and ran the rinse and drain cycle. It has been working beautifully ever since.

Remove the screen that runs along the back of the dishwasher.In the middle of the area that was covered with the screen you will see a white plastic valve with 2 little ears sticking up. Use the nose of a pair of pliers to twist counter/clockwise on the valve and it will come right out. Inspect the valve.If the rubber cone shaped valve inside the valve can be pushed through the top of the valve ,the valve is bad.Replace it and go wash your dishes.

Remove old piston assembly with screwdriver and tapping hammer inside the machine and screw the new part in hand tight, all done works fine

The part that took the longest was taking the washer out from under the counter. The fix was the easy part = 15 to 20 minutes no problems. After putting the washer back and reconecting everything,the first cycle I had some leaking around one of the two big clamps. I had to pull it out again and move the clamps around and tighten them. Much better the 2nd time around, Good to go!! HAPPY WIFE HAPPY LIFE !!!! Good Luck !!

first I removed the screen in the back of dishwasher and then I replaced the check valve

I read the reviews on line and followed the advice the part was easy to find and easy to replace once I got the screen off it came right out with a twist. and right back in reverse order, I fired it up and it drained, yay! no more stinky mess and no call to the appliance repair guy,

i unscrewed the 4 screws in the back, took off the guard thing, and unscrewed the existing part with my hand. put new part in and ran dishwasher. the part did not fix the problem, now i'm on to maybe replacing solenoid? i have no idea. this part was simple to replace though. hope i can fix this issue, i need my dishwasher to run right!

remove the four screws in the back of dishwasher on the inside. Remove screen. Remove the piston nut assembly for the check valve. Re-install the screen and four nuts and your done.

Once I found out where the pison was it was easy. I removed the far back screen that runs across the entire back of the inside of the dishwasher. There was four screws to remove this screen. This exposed the Piston assemply which is threaded, so you just twist it off like a big nut. It was easy to tell that the rubber on the piston was not sealing and needed to be replaced.

Followed the directions from the website and removed the plastic screen from the back of the washer (4 bolts). The Piston and Nut assembly was easliy removed with a few turns, popped the new one in, and re-installed the screen. Everything works great.