GLD4460NS General Electric Dishwasher - Instructions

so easy! Ordered the rollers and clips ... popped them on and done!!!

i needed new rollers and inserts to keep wheels on now its like new when i pull out bottom basket

Simply replace wheel

Remove bottom articulating sprayer and water fittings. Remove and replace filter

Parts were easy to find, easy to order and arrived prior to the advertised delivery date. Instructions for replacement were easy to understand and in about 10 minutes the old part was removed, and the new one installed. thanks for your prompt and efficient company.

just snapped the new part in. couldn't have been easier

Removed screws that held dishwasher under cabinet...pulled out DW...removed old part...replaced with new....easier than falling off a stump.

Open dishwasher. Remove the screws on plastic cover of door. To cover off back of plunger replaced with new one. Reinstalled screws in door and everything worked

Replaced the middle spray arm and bearing using a nut driver.

First thing to do is remove all the dishes or you will have an issue with broken dishes. Naturally you will need to get the dishwasher on it's front so you can get to the inlet. First remove the two screws holding the pump on to the frame of the machine. They are long and in a tight spot so a ratchet wrench works best, I think they were 8mm but maybe 10. Next take the clamp holding the pump on the sump. Give the pump a slight pull and it will come off, and set it out of the way. Next look for another clamp. Disconnect it. Finally you will look at the top where the sump goes into the actual washer itself. There are two "U" shaped clamps holding it on. From behine they will look like U's that are facing each other while laying on their side like this. (o) They are holding the sump on and their are two bolts in each. Once again, a ratchet wrench works best. Remove those bolts and give the sump a pull and it comes right off in your hands. Then reverse the steps and put it back together. Also ensure you cut the water off under the sink, to reduce the mess. Hope it helps.

Laid on floor remove two small bolts with nutdriver,loose water line with wrench,remove other water line with pliers.Remove water inlet valve and replace with new one

first off if you can understand the problem DO NOT CALL THE GE REPAIR SERVICE AND HAVE A REPAIRMAN COME TO YOUR HOME you will save over $300.00. a mistake i made, it cost me $79.95 just for him to tell me the dishwasher was broken and then i was told it would cost me over $300.00 to fix it. WHEN I TALKED TO PARTSELECT I FOUND THE WATERVALVE FOR A LITTLE OVER $55.00 WITH SHIPPING IT TOOK ABOUT 20 MINUTES TO DISCONNECT THE DISHWASHER AND REMOVE THE OLD PART AND ABOUT THE SAME AMOUNT OF TIME TO REPLACE THE NEW ONE THEY EVEN HAD GOOD INSTRUCTIONS IF YOU NEEDED THEM. I FOUND PARTSELECT SERVICE TO BE A VERY GOOD BUSINESS TO WORK WITH. ROY F BURTNETT

Cut power and water flow to the appliance. Laid appliance on its side, removed the electrical lead from the motor. Remove the mount from the back of the motor and loosened the two clamps- one to the sump and one to the discharge tube. Removed and replaced the pump/motor assy. with the new one, reinstalled the clamps, rear mount and electrical lead. Righted the unit and fired it up. Worked fine.

I carefully read over comments from other people's experience first. I removed all the screws from the inside panel and had several heavy books to weigh down the door. This allowed me to remove the white inside panel, turn it to get easy access to the seal at the bottom. All that was necessary was to clean the area of builted up soap etc, start pulling old seal off from one side and at the same time insert the new seal in same track and groove, being careful to have the new seal lined up in the same manner as the old. The whole process was rather simple and required very little effort.

We tried cleaning the sprayer by unclogging the spray holes but it didn't last very long. I decided to see what it would cost to replace the piece. I have used this site before and love how easy it is to find the part you need. The sites have good pictures so you feel very good that you are ordering the correct part. They also have helpful suggestions for problem.. I ordered the part and it arrived two days later and we installed it right away...I started the dishwasher for a test run and forgot how loud it use to spray..The prices are also great just a service call from a repair man would of cost me triple what I got my new part.