GSD4000NB General Electric Dishwasher - Instructions

All new seals

removed the rack and snapped the 4 week/axle assemblies on rack by hand pressure returned rack to track.

replaced new wheels

just snapped the new part in. couldn't have been easier

pulled the motor and impeller apart noticed that the the impeller blade bent. I got the new part and put it back together

door gasket dried out due to not using the dishwasher very often and needed to be replaced. removed door, replaced gasket, and re-installed door.

I disconnected the pipes to the inlet valve. I removed the bolts from the bracket holding the valve. I tried to use two wrenches to remove the brass angle pipe thingie off the bottom of the old valve. I then beat on it with a hammer, then I just threw it against the basement floor till it came off. I would recommend getting a new brass angle pipe thingie before you start.

i first order the corner baffles and put them in. no change at all, still leaked terribly. the old baffles looked pretty good so i kept them. i then ordered the door gasket and the insert. i removed the old one, put in the new, and still no change. i thought perhaps the machine hadn't been used at all because it was like brand new inside, and previously owned by 'a little old lady'. i decided to load it up and run it on a regular wash, and have done that three times now. it drips a very small amount on the left corner but i'm quite happy that it decreased so much. I think perhaps the seal might be setting with the heat of the cycle because each time a load goes through it get less and less drips from that corner. The first order was sent by ups and they couldn't find where i lived so i actually had to go pick them up, but the second order was sent fedex and they had no problem finding my home, and i was very pleased with how fast my order came.

Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.

remove front lower cover, 2 philips screws, turn off water supply under kitchen sink to dish washer, turn off power to dish washer, remove water supply line to valve, remove power to valve, clip ons, remove two 5/16" screws holding valve on, turn valve gently to access clip holding washer supply hose, push clip up hose and hold hose while pulling valve off. re-install in reverse order, a flash light helps.

Removing two screws holding the bottom trim/sound baffle opened a view of water dripping from the water intake valve at the left front of my Monogram dishwasher. I then turned off the local (under my adjacent sink) separate feed valve for the washer, then opened the (dedicated) breaker for the machine at my breaker panel.

The replacement valve was identical form and fit to the original. It included the replacement mounting bracket integrated with the valve.

Removing two additional screws holding a bigger sound baffle backed with foam gave good access to replace the valve. The foam was fitted to the power box and a few other obstructions, and apparently stuck to something near the top. I ran my hand up separating the foam from the panel and both then came out easily. I reattached the foam to the panel with clear silicon adhesive.

Removing two screws from the front edge of the bracket holding the valve allowed dropping it down for fairly easy access to the clamp holding the flexible house from the valve to the washer. There wasn’t much slack, so I reached the spring clip with a long plier-like device with cups on the working sold as automotive hose clip tool for that purpose. Regular pliers would likely work, with more skin loss from hands.

That action then allowed pulling the valve out from under the machine (feeding slack in the flexible feed I have installed years ago between that valve and the one under my sink. A small adjustable wrench then made easy work of disconnecting the hose brass coupling from the valve.

The right-angle adapter between the valve body and flexible feed hose is apparently specific to the installation, so it had to be removed and attached to the replacement valve. That was facilitated by placing the valves in a large bench vise, clamping the mounting bracket with the right angle adapter up, and using the adjustable wrench again. The old valve had residue from metal pipe thread sealer, so I used some new sealer on the adapter when installing it. Take care. Getting some inside the valve might be a serious problem. Turn the adapter with the adjustable wrench for a snug fit facing the same direction as the plastic nipple for the machine-side hose.

Installation proceeded easily in reverse of the removal process, using a bit of care to fit that foam back around the intended machine projections. I actually used identical thread lattes screws (wider flange) to hold the upper baffle because I misplaced one of the original screws and decided to originals were distorting the mounting slots because the flanges were too small.

I ran the machine through two cycles before replacing the bottom trim, just to assure there were no leaks. Mild panic when the intake valve didn’t operate as soon as I expected, but it must have been some out of phase control operation, because it eventually operated, then operated as expected during the second cycle.

Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.

I unscrewed the front of the door almost to the bottom hinges and removed the latch. Went on line and ordered a replacement. The replacement arrived in a couple days (yeh), was identical to the one I had removed. I could have used another hand but went ahead and replaced it myself. It worked perfectly and I screwed everything back in place. I'm a 73-year-old female, good at taking things apart but not always good at putting them back together but will try anything. Was elated that I could repair it and it actually worked. Great service from your company!

Troubleshot and found that the solenoid had burnt up locking the drain door in closed position. I ordered solenoid, Note: I only received the solenoid. I used the old bracket and springs along with the piston arm for the solenoid. I had to break it free from the old solenoid. Once I got everything cleaned up and put together it took me about 10 minutes to install the solenoid. I manually tested mine prior to wiring back up to ensure proper movement and then tested to ensure that the piston arm did not pop out of the solenoid base.

After installing the part, ran the washer once more. The water still remains in the washer. Tried washing several times. The problem is still the same.