PDW7380NS General Electric Dishwasher - Instructions

This isn't a terribly tricky repair, and the parts are cheap so it's worth a try!

(I had one tricky thing which was the door actuator broke while the door was shut. So I had to get the machine out of it's space without being able to open the front of the machine. I did this by lowering the feet in the front of the machine and then I used a hammer and flat chisel to break the two metal screws I had holding the top of the machine to the top of counter top...a little tricky!)

Remove screws from inside lower panel (where you put soap..the bottom) this will allow you to remove the inside of the door. But be careful as there are still wires attached so be careful to place the inside part without stressing the wires.

I needed to remove the metal harness and to open the black rectangular box that holds the interlock plunger so I could remove the plunger and spring (don't lose..and remember how it goes. take pictures if necessary). Then I was able to remove the broken actuator and see how it all fits together. It rests on top of the latch with notched side facing the inside of the machine. Make sure the notch is centered around where the interlock plunger is located.

Once you have the pieces fit together insert them into the door. Replace the plunger and spring and close the black rectangular box. Then replace the metal harness.

Hold everything in place and put the inside of the door back into position and lock it down with the screws.

You can test the door to make sure it's working but the whole mechanism is less functional when the machine isn't secured into its space. So, if you're mostly sure you've got it right, resecure the machine into its space making sure it's solid and then you should be good.

Like most everyone here I was very happy to accomplish this repair without calling in the repair service!! Awesome.

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

Disconnected the electricity, the drain hose, and the water supply from the dishwasher. Loosened the two screws from the countertop and pulled out the dishwasher. Turned it on to it's side. Saw the damaged inlet sump. Had to remove the Pump connector to get to the inlet sump. Checked it also and discovered that it was starting to develop a small crack from the inside. I decided to replace it as well. The job involves removing the hose clamps and removing the spray mechanizm from the interior of the dishwasher to spin out the inlet sump. Not a difficult job.

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.

I watched the video, read the instructions and went to work. This was the easiest repair I have ever done. I'm 71 and if I can do all 3 spray arms in a total of 15 minutes, anyone can. The hardest part was getting up off the floor when I was finished. The spray arms were all clogged, we have very hard water.

Open dishwasher and remove the bottom spray wheel, filter, and unscrew the mounting bracket to release the pump connector below the bottom of the unit. Remove mounting screws at top front of dishwasher and carefully slide the unit out; you may have to pry side panels inward with a flat screwdriver in order to get the dishwasher past any cabinetry. Be careful not to pull the dishwasher too far out as the water supply and drain hoses could be damaged. Unplug the unit. Turn unit sideways and tip over onto its' back. At this point, the sump will have to be removed using a nut-driver and/or socket set. This will open access to remove the old pump connector. Replace the old connector with the new connector, and reassemble the sump, connecting and firmly tightening all connectors. Tip unit upright. Screw mounting bracket back into the bottom of the dishwasher and put the remaining parts back. Before pushing the unit back into it's nook, I advise running a quick cycle just to make sure there is no leakage. If there is no leakage, put the unit back, tighten the mounting screws and you're done.

get fingers between lower spray arm and drive flange - rotate arm counter-clock wise and lift off...the arm was warped and hitting inside of lower door liner.

unscrewed dishwasher from cabinet, then I flipped dishwasher on it's side. loosen pump motor bracket arm on the end of the motor. loosen pump motor to pump conecter hose clamp and then unscrewed pump motor connector from dishwasher. To install I did the reverse. very easy.

Easy repair-removed hex nuts and and screws to pop out old part and replace with new one. New part works better than the original! 1st replacement part arrived with a broken piece, a quick, courteous phone call got a replacement sent out. It took a 2nd phone call to obtain the refund, but the customer care reps are efficient and friendly. I would order from them again for positive service reasons alone.

Remove Base Access Panel; Removed Valve Mounting Bracket & Valve; Disconnected Wire Connector; Disconnected Supply Line & distribution Hose; Reversed the Process. Piece of Cake; Part was O.E.M.Component Exact Fit; Took Longer to Write this than it took for Fix. Thanks I Will Be Back for other Parts.!

Pulled out the old one put the new one in . Simple and easy

Turn off power and water from dishwasher. Remove Base Access Panel. Remove the upper 2 screws that holds the dishwasher in place. Pull out dishwasher. Locate the valve and remove the 2 screws holding the mounting bracket. (I used a hex Nutdriver to remove the screws) Remove the valve. Disconnect the wire connector. Disconnect water supply. (Place a towel to catch the water) Loosen the hose clamp holding the inlet hose and remove the hose. (I used pliers to loosen the clamp) Remove the elbow from the old valve and reattach to the new valve. (Use teflon tape around the threads) Reverse the Process. Check for leaks. Piece of Cake. Part was an exact fit.

I watched the parts select video and followed their instructions. Only “ issue” was there were no screws on the door behind the exterior skin as in the video, so lifting the inside door liner to put the new lower door seal in was concerning. I was able to pull the liner up enough and slid the seal in with no problem. The video was the key to a smooth repair.

oversized outlet not available in local stores, this one fit perfectly

Removed the lower rack and installed new wheels with clips