PDW8700LW General Electric Dishwasher - Instructions

went to sears and was told axles not available ! after they sold my wife all 8 wheels in two diffrent colors. started looking on line found your web site I entered my model number. In a matter of minutes I found the parts checked stock ordered them and recived conformation.
prices and shiping are fair. ordered recived and installed parts in 4 days WOW ! wished all purchases went this smooth.

Von Neal

Really all it took was removal of the old wheels which would not stay on anyway and the installation of the new ones. That required the axle and wheel being put together and the installing both of those on the lower rack. I was about to buy a new dishwasher when the salesmen told me about a product called Lemi Shine it saved my hundreds of dollars and the inside of my dishwasher looks brand new. With my new wheels I am good to go again.

but axle on new wheen and put axle on tray

these appeared to be a newer design of wheels and wheel hubs that fit much better and seemed more stable. Very easy to replace and the bottom rack of our dishwasher works great now!

Simply pull out the old axle and snap in the new one. It is simple. Also the replacement axels were MUCH better quality than the originals. The bottom tray now slides in and out very easily. Note, if you have this problem, you do not need to replace the wheel, just the axle.

This was a simple part swap. The stud rollers are the small peg-clips that hold the wheel on the lower dish rack. Removing the old stud rollers from the wheels required a pair of pliers. I then popped the new stud rollers into the old wheels and snapped them back onto the lower dish rack. I scored some major points from my frustrated wife -- easy, fast fix!

I simply removed the old (broken) stud rollers by pinching them with a needle nose pliers and pushing them out, snapped the new stud roller in the wheel, and snapped the wheel onto the lower basket unit. If you have all of the wheels and they are in good shape, you do not need to buy new wheels, the new stud rollers work just fine with the old wheels.

Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!

shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.

Removed the dishwasher to get at the defective parts and removed,than replaced the two check valves and reassemble.

Followed the instruction video on your website. It was accurate and valid. The repair should have taken 15 mins., instead one of the screws holding the dispenser was frozen. Tried DW-40, and liquid wrench. Neither worked because the screw was in plastic.Finally got out the Dremel and cutting wheels. Had to cut away enough of the unit until I could get at the screw (it was the center bottom one). Sliced through some more of the housing, then cut a notch in the screw head deep enough so I could apply enough pressure with a flat blade screwdriver to open it. After that things went as smoothly as could be expected.A bad design and cheap materials.

Turned off the power at the main box. Removed the six phillips screws and two bottom hex screws holding the front panel. Removed the two solenoid wires on the old dispenser (Label wire polarity). Removed the eight screws holding the old soap dispensor and took it out. Cleaned the area around the hole. Laid down a bead of silicon caulk around the hole edges. Placed the new dispenser in the hole and replaced the eight screws (do not over tighten). Replaced the two wires on the dispenser solenoid (check polarity). Replaced the front cover (Do not over tighten. Turned on the power and job complete.

Repaired the soap dispenser.

Pull out the old, died gasket. Clean out track that holds gasket. insert new gasket.

The repair is just a couple of minutes job. All I had to do was to pop the wheel axle in the new wheels, remove the old wheels and put the new ones in. The wheel axles on the original one, were like clasps. All one needs to do is to pull the clasp to one side and slide the wheel out. The new one, just needs to be pushed in. In my case, I could have just swapped out the axles, but decided to change the whole set anyway.