GLD6800N00BB General Electric Dishwasher - Instructions

The repairman diagnosed the problem as a control board failure and quoted a $350 bill. I self-diagnosed it as a failed interlock switch -- and found out that the switch was OK but the cover was cracked, preventing the switch from functioning normally. Total repair bill - $1.50!

Installing the gasket took about 45 seconds. It actually took more time to scrub the area clean prior to installing. One quick trick I found was to fold the replacement gasket in two, and use that mark to center the gasket and press it in from there. That way you don't have any guesswork as to how much slack to allow for when starting.

The bottom rack just pulls out so that was an easy replacement. The upper rack required a 1/4" nutdriver to remove the sprayer from the rack and a slot screwdriver was used to remove the tab that was holding the rack to the slide arm. Total time, 10 minutes tops!

Disconnect electrical power & shut off water supply. Remove front panel covers. Removed mounting screws (2). Unhooked water supply line & flow line. Took off old brass adapter fitting. Teflon taped fitting to new inlet. Performed reverse procedures. It ran just fine!!

First, I took off all the pipe clamps and retaining brackets. Then, I pried it out of there. One of the tabs holding one of the other bits to the body got busted, but it didn't matter, as it is held on very well just by the pipe clamp connection. I stuck the new one in and re-attached all the hoses. The GIANT complication was that a new floor had been installed over the old floor, right up against the kick plate- so in order to remove the dishwasher, I had to slice open the counter, as the new floor prevented sliding it out. To prevent the problem recurring, I spray painted over the sump inlet to make it taste worse. This is the downside of a cat door.

Took screws out of door. Slid bottom seal off and slid new one on.

The repair was really easy. I ordered the part needed after looking at this website. I figured out the problem by looking into the forums. I ordered the part. It came within several days. I got home from work and after dinner pulled the dishwasher from under the kitchen counter. It was easy to do. I flipped the dishwasher on its side. Then removed the old part. It had a water inlet that required a fitting to be loosened with a wrench. It also had a flexible water fill that was attached with a cable clamp. (Remember to turn your water supply off first!) The wiring was disconnected by a simple harness. Four bolts had to be removed to pull the part off of the dishwasher body.

Installation was the reverse of this process. Have been using for a week now and the problem is corrected. Doing business with Parts Select is awesome. I know that over the last several years I have saved tons of money and learned that I can fix nearly any appliance by viewing this website.

Remove screws holding old hose. Attach clamp to new hose with nut driver. Tighten hose and clamp around attachment.

Easy as cake. Perfect part!

i looked on this website and found out which part was the drain pump. the pump was fastened to a drain hose, the dishwasher and power supply. unhooked power supply, noting which color wire belonged where. loosened the hose from the pump, got the new pump, installed. viola!

Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!

I found that the supplied part did not have threads to receive the bolts that were used in the original part. I had to locate thin nuts and bolts and very awkwardly fit those in behind the part. The orignal part would have just bolted on from the front. I almost returned the part as unsatifactory, but decided to make do. Otherwise it would have been a 10 min job.

No Plumer could help me. No one heard of a dishwasher check valve. My dishwasher was an ISA. I was lost until i found the relationship to Kitchenaid. Then sears. Vuela!
The valve was there, but unavailable.
A few more links, and the term "flapper" came up.
Well, my dishwasher check valve HAD a flapper inside. Although a plastic pos, i could unscrew the two halves and see the flapper.
A little piece of rubber, about 1" in diameter
All suppliers gave me but two choices. One large (size given) one smaller.
After years of searching, all I needed was a flapper valve. Not the whole check valve.
I found it hear for under $10

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

I took the front off of the dishwasher door, loosened the screws, unplugged the module and replaced it with the new module. This repair was the easiest repair I've ever completed!

My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!