GSC3200Z02BL General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark L from Dover, DE
- Parts Used:
- WD27X10223
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Panel looked lik an import. Holes did not line up with factory holes.
Held panel in place and drilled holes and installed drill screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Bayside, NY
- Parts Used:
- WD08X10057
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Small leak at the bottom of dishwasher
Removed existing gasket seal on door. Cleaned really well with a household cleaner around the gasket crease. Installed new gasket seal around door. Started with small notch in the middle of the gasket to center on top and then slowly fastened into door edge and slowly snug around bottom edge where the deal is notched and the the difficult part was to feel the seam again on the bottom to re attach seal after notch from corner. Rupert this on the other side of door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- cliff from knoxville, TN
- Parts Used:
- WD13X10003
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Faulty Dishwasher Door Latch
Had to install a new door latch. The installation itself is really quite simple involving removing (separating) the inner door panel to access the latch assembly. The latch is removed by simple push through one slot with a screw driver and the new unit basically pops in through grooved slots. However, I did find it quite helpful to first (and during) review a YouTube video illustrating the replacement. Although it is largely a simple procedure, for the first-time "installer" there are still a few tricky nuances to be aware of.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mimi from Philadelphia, PA
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Old pump leaking
The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Willcox, AZ
- Parts Used:
- WD19X10032
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Leaking motor seal
Followed easy instructions and completed repair in less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from Town of Tonawanda, NY
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
motor fan broke
I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Oronogo, MO
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
existing gasket dry rotted
This repoair was needed due to diswasher leaking out of side door. I just moved in about 6 months ago and needed to use dishwasher. When it leaked i noticed it was in need of a gasket. I searched the internet and came accross "part select". Part showed up in less than 3 days and was a breeze to install. The original gasket came out just by pulling, cleaned up channel and installed new gasket.slid in real easy. I did take off inner door panel to inspect for any damage. none noted. Perfect fit first time. Dont get confused folks if the part has another name as some parts are interchangeable in the industry.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Burl from Spring Valley, IL
- Parts Used:
- WD26X10013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Motor failure because of black power wire separation.
Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heidi from North Las Vegas, NV
- Parts Used:
- WD02X25492
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Right door spring broke
Took lower panel off with screwdriver. Removed old spring. Attached new spring. Very easy, and I'm a woman. LOL
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Bradenton, FL
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishes cloudy, spotting
Unscrew old stripped out one and put in new one ..wala!! Easy repair for this old lady...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Merwyn from Lima, OH
- Parts Used:
- WD28X10007
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
tower cap broke
simply snap new one in place. I will have to say your service was fantastic. I received the new cap 2nd day. I am very pleased and would not hesitate to order something else if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Yucca Valley, CA
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The smallest portion of the sprayer had been broken
Grab the large portion of the assembly and unscrew it- if you've got hard water, this may take some serious effort. Screw in the new part, and your good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from Mt. Pleasant, MI
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tower Broken
Order new part. Lightning fast delivery. Unscrew old one, put in new. 30 seconds. Don't get any easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leanne from Divide, MT
- Parts Used:
- WD12X10284
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rinse aid fill cap was stripped.
I removed the old cap and put on the new cap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from Hubbard, TX
- Parts Used:
- WD22X10008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
would not clean the dishes
I unscrewed the lower spray arm and support assembly and then screwed the new part in. Very easy.
Was this instruction helpful to you?
Thank you for voting!