PDW7912N00SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gail from Woodstock, GA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
axle for wheel was broken
Popped the axle on to the wheel, then snapped it on to the lower drawer - done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Durango, CO
- Parts Used:
- WD12X10278, WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
some wheels had broken, was really hard to move rack in and out.
I am NOT handy, but my husband was gone when the wheels and stud/axles came. I was able to replace all of them in about ten minutes with no tools. Easy and no more frustrations!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Palatka, FL
- Parts Used:
- WD28X25960
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old rack was rusted out and missing most of the wheels.
Easiest repair ever. My new rack arrived in three days, opened the box and slid it in. Better quality than the original. Excellent service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Carlisle, PA
- Parts Used:
- WD12X10163
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Detergent cap would not stay closed
After removing the screws, the front of the dishwasher easily came off. I put 2 screws back in to hold the control panel in place. I did not want that to dangle while replacing the part. The part came off easily after removing the screws. Everything went together easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- donna from walworth, NY
- Parts Used:
- WD12X10304
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
upper dishwashr rack lost the end cap and the rack kept coming off the track when you went to push it back in it would jam into the track and all the dishes would bang and fall.
placed the end cap into location and forced it into place. Fixed -and we are all much happier!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Cicero, NY
- Parts Used:
- WD35X20994
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Roller Broken on dishwasher
Popped out Old Roller, put in new one, pushing it together with a pair of pliers.
My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item
Check all your rollers before you buy just one!!!!!
My only regret is that i didn't check the other side of the dishwasher... the other roller was broken also, and now i have to pay 5.95 shipping & handling for a .29 cent item
Check all your rollers before you buy just one!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from FAIRFIELD, CT
- Parts Used:
- WD28X24469
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Holes in old dishwasher basket
The replacement dishwasher basket easily fit in my dishwasher. Easy to order. Quick delivery. Highly recommended.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from WALNUT CREEK, CA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken axle which hold wheel on lower rack
Easy install, snap in new axle and put wheel on stud. Be sure to check all wheels for any replacement due to heat melting wheels on rack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Faye from E STROUDSBURG, PA
- Parts Used:
- WD12X10278
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old wheels kept falling off
Took stud out of old wheel, put new stud in. It was that easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Waterville, ME
- Parts Used:
- WD12X10304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
PS259168 Replaced broken end cap on upper dish rack
No tools needed for this half-minute repair. Just bend the flexible plastic tab on the back of the end cap until it slips into the metal rail and the end cap snaps into place. Couldn't be easier or simpler!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from SOUTHPORT, NC
- Parts Used:
- WD12X10304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
rack slide end cap broke
Slide it into the arm until you hear it snap
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from STERLING HTS, MI
- Parts Used:
- WD12X10064
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Tine retainer was broken
I lined up the tines with the bottom basket and snapped it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Prasad from LEAWOOD, KS
- Parts Used:
- WD21X10169
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Dishwasher was not starting
Replaced interlock assembly as one of the possible causes. The replacement was easy, but this was not the final fix. I also replaced the water inlet valve, flood switch and finally found that there was large calcification within the drain tube assembly (not visible, but was blocking water). Got a new flexible tubing and new drain hose, plugged everything together and the dishwasher runs like new now. Watching for a potential leak from the drain tube to drain hose connection and mya need to tape it up, but so far so good...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from DELANO, CA
- Parts Used:
- WD35X20994
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Rollers worn out, top rack would not slide open or closed without wiggling around.
Removed rack, removed old roller pieces, installed new, replaced rack , and works as new now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bob from Chandler, AZ
- Parts Used:
- WD28X25960
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Due the the age of this dishwasher (13 years) both upper and lower racks were showing significant rusting.
This lower rack (GE part #WD28X25960) was ready to roll right into the dishwasher straight out of the box, no tools needed.
Was this instruction helpful to you?
Thank you for voting!