Models > 402070

402070 General Electric Dishwasher

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for 402070

Viewing 5 of 5
Keep searches simple, eg. "belt" or "pump".
The wheels on the lower rack of your dishwasher allow for the rack to slide in and out smoothly. If this is not happening, it may be necessary to replace one or more of the wheels. This kit includes 8...
In Stock
This is a genuine OEM replacement axle for the lower rack in your dishwasher. The axle is used to mount the roller wheel to the rack. If it becomes damaged, you may have difficulty gliding the bottom ...
In Stock
The rack slide end cap attaches to the rails of the upper dishrack, to prevent it from sliding all the way out. It is a one-inch white plastic part that can break over time. This might be the part you...
In Stock
This is a kit of 4 which includes the wheels and axels.
In Stock
This basket is part of a silverware basket that has 3 sections. This is the middle section of the basket.
In Stock
This door recess spring or dispenser lever spring in your refrigerator is used to return the ice door to the closed position or the dispenser lever to the home position once released. You will find th...
In Stock
This dish rack is for dishwashers. Dish rack holds the dishes in place during the dish washing cycle.
In Stock
This part releases the detergent and rinse aid into the dishwasher.
In Stock
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of wat...
In Stock
The lower spray arm is mounted to the bottom of your dishwasher tub, and it rotates and sprays water to clean the dishes in the lower dish rack. This spray arm is made of gray plastic, and is approxim...
In Stock
This is a handle actuator for your dishwasher. It is made of black plastic, and is sold individually. The handle actuator is found in the control panel, and it releases the door latch when you lift th...
In Stock
The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In ...
In Stock

Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

Common Problems and Symptoms for 402070

Viewing 18 of 18
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not cleaning dishes properly
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door latch failure
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Not draining
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not dispense detergent
Fixed by these parts
Fixing Fixing
How to fix it
Will not fill with water
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door Sweating
Fixed by these parts
Fixing
How to fix it
Not drying dishes properly
Fixed by these parts
Fixing
How to fix it
Ice maker won’t dispense ice
Fixed by these parts
Fixing
How to fix it
Door won’t open or close
Fixed by these parts
Fixing
How to fix it
Frost buildup
Fixed by these parts
Fixing
How to fix it
Not dispensing water
Fixed by these parts
Fixing
How to fix it
Freezer section too warm
Fixed by these parts
Fixing
How to fix it
Ice maker not making ice
Fixed by these parts
Fixing
How to fix it
Freezer not defrosting
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Mark from Huntingdon Valley, PA
Parts Used:
WD35X21038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
520 of 542 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Teresa from Phenix City, AL
Parts Used:
WD35X21038
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The rear wheels were missing on the lower rack.
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
475 of 487 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Naperville, IL
Parts Used:
WD12X10163
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
soap door latch broken, wouldn't hold soap for later release in middle of cycle like it was supposed to.
Turned off power to unit, 'cuz it has a solenoid lead to open the soap door.
Removed the phillips head screws that held the door together. The screw are located on the inside edge of the door, there are 10-12 of them.
Spearated the door shells carefully, trying not to disturb the location of the wiring in the middle of the doo r.

Found the 4 screws that hold the module assembly to the door from the inside, and removed them.
Popped the assembly out, cleaned the gasket-seat area and placed the new one in place.
Carefully tightened the 4 screws. It is easy to over-tighten them, so only turn them until you feel they are snug. Let the gasket do the work.
Attached the two solenoid control wires in the same positions they were in before they were removed from the old assembly.
Re-assembled the door halves, again taking care to not over-tighten the phillips-head screws. One got "spun" and I removed it and re-set it into some epoxy.
Returned power to the dishwasher, and stopped washing dishes by hand.
Note: the latch is now made with a plastic that is more dense, and likely will not fail as soon as the original one did. I think GE learned something about the durability of their component plastics since this was originally built.
100 of 105 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!