VDB6110LD129 General Electric Dishwasher - Instructions

pretty easy, take off 7 screws from inside door

only hard part was getting arm to click into lever through the door. if you practice with the parts outside the door they lock together really well :)

My suggestion is to replace all four rollers at the same time since they are all the same age. Fortunately, four rollers come in each pack you order. You need to remove the end cap on borh metal rack rods which takes a little doing. You cannot just pull the caps off. You need to twist the end cap to free up the little catch at the rear of the end cap. Once the end caps are off, just pull of the old rollers and install the new ones, replace the end caps and you're done.

Very simple repair: assemble the wheel/clip assembly. Attach to lower dish rack.

I was very happy with the fast delivery by PartSelect.

took off the end clip, pulled the old wheel off and unclipped the bracket from the rack, then clipped the new assembly on...Simple!

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

We ordered the pump kit by model number and it was a perfect match.(It was on our door step in 2 days with normal shipping!) Three bolts and a couple of electrical connections later and the pump was off The install was just as easy. The instructions were very easy to follow.It's great to find a company these days that knows what it is doing and does exactly what it says it will do.
Kudos and thanks!

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

Shut off water, disconnect power,remove
Faulty valve,install replacement part.

Pulled the lower left side end of the old door gasket out of door gasket retaining slot and slowly and evenly continued to work my way around the door pulling the door gasket out of the retaining slot until I reached the end. I installed the new gasket into retaining the retaining slot beginning on lower left side and then slowly and evenly working my way around the door inserting the new gasket into the retaining slot. I was careful to make sure the two cutout portions of the new gasket's retaining edge were correctly positioned in the lower corners of the door.

We ordered our motor and pump assembly. When it arrived we followed the instructions that came with it. We had no problem with the instructions. We found it to be really easy. I was very happy since this happened 4 days before Thanksgiving. Thanks for the easy instructions, my husband got my dishwasher repaired in plenty of time for our Thanksgiving family get together.

As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.

I removed the dishwasher, removed the front kick panel, layed the dishwasher on its back, loosened the clamps and removed the old motor and pump assy. Cleaned up the area where the unit was, Installed the new unit, tightened the clamps and it was done. Probably took around an hour because of my cleaning up the sealing areas.

Without any specific directions with the part (which would had been nice. If it wasn't for my husband I wouldn't have known where to start.) I had to carfully pull the dishwasher out of the cabinet (it wasn't heavy) to unplug the power supply. Then we unscrewed 2 screws on the top and the upper arm connection came off. We replaced it with the new one, screwed it back on, reconnected the power supply and pushed the dishwasher back where it belonged. It worked out very well.
Also I want to say I am very happy with the length of time it took to get my part to me. (1 day) I was washing dishes it no time.

Thank You
Debbie Bradford
Hookstown, Pa.

Had to remove entire lower unit from dishwasher but it is a tight fit between the pump inlet flange and the floor.The next problem was to get the E clip off of the valve shaft. I knew the E clip had to be a straight fit when put back on the shaft so I had to straighten out before putting it back on the shaft after putting the new seal on the shaft correctly.Put the solonoid back on and made sure the valve shaft turned freely. Next fun was getting the pump unit back in place. Not easy (clearance) but got-er done!