GSD5911D01WW General Electric Dishwasher - Instructions

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

First I opened the package and screwed the new dispenser cap into place.

Inserted wheels on socket and then into the dishwasher rack.

Removed the lower rack and installed new wheels with clips

Simply screwed in new cap

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

Removed seven screws that held the inside panel to door. removed inside panel to work area and cleaned. After carefully observing the position of the old gasket, it was easily removed and the new one but in its place. Replaced the door being careful toalign the handle before tightly securing all seven screws. Repair worked, no more leak.

REPLACE CONTROL BOARD - Turn off circuit breaker. Take out lower rack. Remove inside door panel (seven Phillips screws). Hold outside door panel (control board location) in place with bungee cord. Remove push lever (two screws) to facilitate removal of control board. Disconnect control board connectors (five, I think). Remove old control board (two screws and plastic clips). Install new control board (clips, connectors, and two screws). Re-install push lever (two screws). Re-install inside door panel (the main contol lever alignment is a little tricky), seven screws. Remove bungee cord. Put lower rack back in. Turn on circuit breaker. Test dishwasher. Worked perfectly, just like new. Normal amount of water in bottom. "Dry" cycle normal. "Clean" light comes on and stays on until door is opened i.e. normal operation. "Delay" feature also works normally. Dishwasher may last a few more years. Cost of control board: $120 inc. shipping.

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

Went to repair parts on troubleshooting and found check valve assembly to be most common problem. Went to parts diagram to locate assembly and found it somewhat confusing as to exact location. Ordered part(s) on percentage as the problem. Received part next day (great)! Pulled dishwasher out and found I did NOT need to do so to replace check valve which is replaced without having to remove dishwasher. The gasket replacement was not necessary as it seals sump area from bottom of dishwasher and not the valve as it appears on the parts diagram. It took about 2 minutes to replace valve itself and it was the cause of the problem.

I had a slow drip under the dish washer that originated from the solenoid shaft. The replacement o ring fixed it up. While I had it pulled out I replaced all the door seals and top rack rollers.

I ordered the parts on a Thursday evening and received them on Friday. WOW now that's fast! The parts came from Illinois and I live in Indiana so that might have helped but I was very surprised and glad for the quick service. I would defiantly order from Parts Select again. Thank you!

First, I drained the water from inside the washer and removed it from under the sink. I wasn't sure if I had a clog in the drain line, so I dissasembled the drain under the sink and cleaned that as well. While cleaning under the sink my wife found her $4000 dollar ruby that fell out of her mothers ring a couple weeks earlier. It must have dripped out of the trap while I had water draining everywhere. Put drain back together and moved on to the dishwasher repair. Parts were easy to install after laying the dishwasher down on its front to access the bottom back side. Hooked everything back up and slid it back under the countertop and away it went. Had one small leak after running (water in line wasn't tight enough). A twist with a pair of pliers and that was resolved.
Fast shipping by the way! I paid a little more for the exit washer than I wanted to, but with shipping only from one source and delivery of parts at the same time made downtime as little as possible. I'm sure I saved $100 dollars or so by using this website for parts and tech info. And recovered a precious stone to boot.

Ordered the part online and replaced the hoses. Very easy...took maybe 20 minutes

Plumber had suggested trying a new gasket rather than replace the dishwasher. Ordered one and installed it. Cleaned door and installed gasket in about 30 minutes. So far it works great .... and ... cheaper than new dishwasher.

Looked up possible causes on your website. Website stated that more than 50% of time the cause was the piston and nut assembly. Removed the piston and nut assembly in bottom of unit behind screen on rear wall and saw that the gasket seal was completely gone . Ordered the part. took less than 10 minutes to install. Tested the unit and it drained completely. Thank you as i was looking at a more difficult repair if the pump had to be replaced.Repair cost less than $20.00.Before changing piston and nut assembly I cleaned the strainer and sump. disconnected drain hose and checked for blockage . i than checked your website that listed the piston assembly as the culprit more than 50% of the time. Thanks again