PDT750SSFASS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- BENJAMIN from ONALASKA, TX
- Parts Used:
- WD12X26146
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
3 Plastic rollers on bottom of dish basket came off and melted by the heating coil in dishwasher,
Simply pick the basket up to slide wheels onto axles and push in until they lock in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from CASTLE ROCK, CO
- Parts Used:
- WD01X10569
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The pulley cable had broken
Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herminio from TOMS RIVER, NJ
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Door 1witch stopped working
1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Benjamin from VIENNA, VA
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
The dishwasher was filling normally, but was not heating the wash water nor heating the dishes for the final dry. Dishes were not being properly cleaned and were not at all dry after the cycle.
I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from LAS VEGAS, NV
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken door latch and springs were not connected.
Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from VENICE, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would pop open after starting dishwasher numerous times before latching would catch.
Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from BROOKFIELD, WI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dish washer would not turn on
took off 2 sheet metal on the bottom, lowered the dish washer, pulled it out enought to unscrew 2 screws, unplugged the old part plugged in the new, put it back together.
Works like a champ.
Works like a champ.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from JAMESTOWN, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door did not latch, therefore would not operate
Replaced latch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamara Van from INMAN, SC
- Parts Used:
- WD22X22853, WD21X20192
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Spray arm and spray head were stripped out.
The pieces just twist and snap together. You have to align the conduit with the interacting items before sliding and snapping into place. The problem happens when the bottom rack is loaded too high and the bottom items hit the spray head.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from CASEVILLE, MI
- Parts Used:
- WD21X10490
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would not sense door was latched
Super easy repair, just removed the old latch and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lonnie from YUKON, OK
- Parts Used:
- WD01X10569
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
REPLACE DOOR CABLE
Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from NEW YORK, NY
- Parts Used:
- WD08X22095
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Dishwasher door was leaking at bottom.
When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from DANBURY, CT
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Ge Dishwasher was not filling with water
I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randal from TWIN FALLS, ID
- Parts Used:
- WD21X10519
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Wife said Dishes were not Drying and leaving Spots !
I tested Heating Element with Ohm Meter-Direct Short (if open it would have been bad and I would need to replace the element. Per the Website Troubleshooting for GE dishwasher, it said Heating Element (65%), Float Switch (32%), or Computer Board (only 3% Chance of it being board). So I ordered Float Switch. Later I noticed that the dishwasher would not change wash cycles from Heavy, Normal or Light.
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott
Was this instruction helpful to you?
Thank you for voting!