ZDT800SSF0SS General Electric Dishwasher - Instructions

The replacement went extremely well, the removal and installation of the unit from the cupboard took more time. The pump came off easily, I had to purchase a steel band clamp to replace the crimp clamp that was on the original pump as I did not have a tool for the crimp clamp.

Removed the top two screws that hold the dishwasher to the cabinet , remove the two screws on the bottom panel and remove the panel. Screw the levelers all of the way up and pull out the dishwasher about 6 to 8 inch. Hook the new cabe on the spring and pull around pulley and attach it to the door bracket. I replaced both cables. Reverse to complete.

Had to trouble shoot to isolated the true fault condition. Checked heating element was good
Researched symptoms on YouTube
Removed and inspected float switch part
Ordered and replaced part.

I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.

The part did not fit at all but not worth it to me to return it. The part I need is about 20 inches in length and the one sent was about 10 inches. I will simply call for this dishwasher to be repaired or replaced.

When new gasket arrived almost two weeks after it was sent out from Green Bay, I took out old gasket, marking which side was in and which out.
Then, with hands, fit new gasket in place making sure it was centered.
No leaking; it worked.
Thanks.

I tested Heating Element with Ohm Meter-Direct Short (if open it would have been bad and I would need to replace the element. Per the Website Troubleshooting for GE dishwasher, it said Heating Element (65%), Float Switch (32%), or Computer Board (only 3% Chance of it being board). So I ordered Float Switch. Later I noticed that the dishwasher would not change wash cycles from Heavy, Normal or Light.
So I turned the Circuit Breaker on and off. This fixed the Wash Cycle.
When the Float Switch Came in, I installed it in a few minutes watching the video on the GE Troubleshooting Page. Later when it was running I checked the operation and when I opened the door, the wife says seeing the steaming water, You fixed it, the Water is Hot now ! It was all about Hot Water, not the Heating Element at all ! And I think everything was fixed when I flipped the Circuit Breaker on and off and re-set the computer board. I think replacing the Float Switch was good maintenance, cause it was really dirty and needed to be replaced soon anyway. And it may have avoided my wife's next misdiagnosis with our dishwasher. This was 2 weeks ago, and all is well.
Sincerely,
Scott

Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,

Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.

Followed directions on YouTube

First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen.
Using the nut driver, remove two screws from the white plastic retainer ring at bottom the flood switch.
I used pliers to grip the ring to take it out.
**Dry everything in the "well" where the flood switch sits.**
Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier!
Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!