YRC3410KW147 General Electric Dishwasher - Instructions

Turned off breaker. Turned off water and disconnected water line to make it easy to pull unit out and turn on it's side. Once that was done it was an easy swap out. Exact same motor/pump assembly. Love this site. Thanks

Pulled the dishwasher out and turned on its back and pulled out the seal. Saw it was bad and order one. It was here in two days and fixed that afternoon. Great service and quick delivery!!! Will use this site again!!

followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.

The part that took the longest was taking the washer out from under the counter. The fix was the easy part = 15 to 20 minutes no problems. After putting the washer back and reconecting everything,the first cycle I had some leaking around one of the two big clamps. I had to pull it out again and move the clamps around and tighten them. Much better the 2nd time around, Good to go!! HAPPY WIFE HAPPY LIFE !!!! Good Luck !!

Unplugged the machine then removed the two connectors to the motor. Loosenned the hose clamps, pulled the hoses took off the balancing bar,removed old motor assembly and put new one in. Reverse all the steps plugged the machine back on and was done in less then twenty minutes.

Most time spent was removing washer out from beneath the counter. Motor and pump installation was a breeze. Everything I needed was in the kit and easy to follow the instructions provided. Saved a lot of money and washer runs perfect. Thank you.

Removed the dishwasher from under the counter, found where the leak was coming from, which took the most time. We ordered the new part on line, it came the next day and the installation of the new part took about 30 minutes and the dishwasher is like new now. This procedure saved us a lot of money.

I disconnected the water line on the left-front. Disconnected the drain line at the air-break. I removed the AC power-in box on the right front and disconnected the power lines going to the unit. I took out the two screws holding the unit to the cabinet (above the door) and slid the unit out onto a drop cloth (protect the floor; some water spills). Pulled the unit out and turned over. Followed the directions with the motor & pump valve kit, which were very easy to follow. Then reversed the above. Nut drivers are a must for this job.

Hardest parts were finding the right size (13/16 in) crow foot wrench to disconnect water to the inlet solenoid valve to slide the dishwasher out. Regular wrenches won't work -- the space is too tight. Very few people have the tools I have. (No directions came with the parts package.) Second hardest was realizing the rubber transition piece connects directly to the rotation spray head inside. Threaded joint mates them up. It wouldn't unscrew, so I agonized over tearing it out piece by piece (the old rubber part I was replacing), but that's eventually what I did. Probably my fault, I could have looked at the expanded parts diagram view I had printed to find the part to order. Overall not that bad a deal, but a pro should have been able to do it in an hour or two.

After doing dishes by hand for four months, I decided to take a look at the dishwasher. It took about 40 minutes to identify the problem and order the part fom PartSelect. The part arrived in two days and took two minutes to install. It's best not to rush into these things.

Remove lower rack from dishwasher to provide easy access to spray arm/hub assembly. Removed hub/spray arm assembly from base of dishwasher by unscrewing it from the base of the dishwasher. You should be able to do this by hand. Then unscrew the upper spray arm from the hub. This is the telescoping tube that pops up from the center, and it is reverse threaded, so loosen it like you're tightening it.Remove the Phillips head screw holding the spray arm to the old hub. Transfer the upper spray arm assembly to the new hub. Screw the whole assembly back on the threaded connection it came off of. Hand tighten only.

Dishwasher had flooded. Removed Dishwasher from cabinet and diagnosed problem. Found "PartSelect" on Internet and found Part kit available at reasonable price, in stock to ship immediately. Part #PS260801 [WD26x10013] contained enough parts to make installation easy and also I was able to cure discovery of slit in drain hose that attached to dishwasher drain outlet because kit included a short piece of hose and a hose clamp that allowed hose that had been trimmed to connect to outlet.

I took the dishwasher out from under the sink and looked at the pump and motor, saw that the cooling fan that this old style motor used was broke. Ordered this kit and installed it. I didn't even look at the directions that simple of a swap. Thank God!

The motor/pump Kit I purchased could fix/be installed in any GE dishwasher made since 1970. I would guess that the one I have is about 15-20 years old. I encountered only one small problem with the kit------ a motor hanger that had to be bent a bit to fit correctly. Other than that it was a total breeze. The clear instructions included in the kit helped quite a bit. In 30 minutes or so ,I was done and our machine was back in operation

Followed easy instructions and completed repair in less than 30 minutes.