YRB0220NB118 General Electric Dishwasher - Instructions

I removed the screws from inside door panel. Took door panel out. Noted the way the old gasket was placed, removed it and replaced with the new gasket. Replaced the door panel. Felt pretty proud of myself until I realized that the door lock wouldn't work when I was going to run it. I have now removed the door panel again and am trying to get the door lock lever to work.

I made a substitute cable that worked ok, but was a bit loose. When the new cable part came in I simply unhooked the substitute and hooked the new part in its place. The two spring ends slip into a hole on the cable connector. The cable loops under a plastic pulley and the far end piece fits over a small retainer. Actually, unbolting the bottom case parts and bolting them back on took more time than replacing the broken cable. The door works fine now.

The hardest part is removing the plastic stop on the end of the two slides that support the roller rack. My unit was very old and I was afraid the plastic was brittle. Fortunately, the plastic could still be bent without breaking. You need to physically bend the plastic stops to remove. They came out easily, but you do need to apply some force.

Replacing the rollers was simple. Replacing the stops was easy once you understand how to pry them out. I would recommend trying to remove the stops with your hand only at first. You are less likely to damage the plastic.

With coin, to remove the end cap from the front inside of the rail, insert the edge of the coin into the side of the end cap and push the coin to the rear while rotating the end cap to the inside of the tray until it comes free. Don't force. Pepeat for other rail. Repeat to reinstall end caps. You can can now slide out the the tray. Use long nose pliers to remove old rollers and insert new roller(s) on same prong. Do all 4. Reinsert tray and end caps.

First, remove the two access panels to the bottom of the dishwasher, each had two screws. Then, disconnect each old door cable and eyelet assembly, and the two springs. Now, connect the two new cable assemblies, and reconnect the two springs, one at a time, between the eyelets of the cable assemblies. Finally, replace the access panels

My GE dishwasher had a problem. The upper rack would fall into the lower rack when loaded breaking dishes! Turns out, the front rollers on the upper rack were broken so that the supports would just pull out. So, I found the parts on this website easily. I then took off the plastic plug on the support which is easy to do. There is a flange you bend towards the rear of the dishwasher to release the plug. Once released you have access to the rollers, which just snap off easily. The new ones snap on easily. Reverse the cap removal, and you are done!

Removed access panel (2 screws), Replaced broken cable/Eyelet assembly. Replaced access panel. Job took 5 minutes, including clean-up & stowing tools.

I have to be honest. At first I called a repair person, but it was Sunday so he couldn't come till the following week. Then my incredibly intelligent, industrious, and internet-savvy wife found your website. We saw that others had had the same problem. The part we needed was right there.... voila! 2 days later I had the part in hand. Not being the most handy of handymen, I followed the directions that others who had the same problem had posted. Yep, it was that simple -- And a heck of a lot cheaper than a repair person. Your website was very valuable, and I definitely will refer it to others looking for a part for a home repair job.

Super-easy and quick repair -- quality part snapped right into place.

Installed new lower rack wheel kit

Took out old one and put in the new one. Not hard at all. Thanks

Removed the white end of the top track. Pulled off the remnants of the rack roller. Slide the rack roller wheel into the track and popped the other end on the top rack (looked at the other rack rollers to see how it fit.) After that, I put the end back on the track.... Note what is the top and what is the bottom of the track end. Realizing that there is a wider area on the track to slide part of the white track end through to get it on without much effort.

I followed the video instructions on removing the rack slide end cap to prevent breaking it and it was very easy to remove and replace the broken one. I attached the new rack rollers and voila we were back in business. I was about to order a new dishwasher the night before for $5oo! Thankfully the stores website wasn't working so I couldn't. I decided to look online to find out if it was easy just to replace the parts. Looks like I saved close to $500 just replacing those parts! AWESOME!!!!!Thank you for a user friendly website. It made all the difference")

removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you

I connected one end of hose to the drain using a hose clamp and screwdriver then connected the other end to the dishwasher using anouther hose clamp and a screwdriver..