GSD5911D01SS General Electric Dishwasher - Instructions

with electric power and water source turned off,I first bailed out the water from tub then I pulled dishwasher out from under cabinet . Then I removed the motor and pump and put it on the table. I took a digital photo so I could remember exactly how everything was assembled. I checked for clogs and damage and realized that the solonoid casing had melted around the armature link assembly . I Looked at diagram for parts name and number and ordered from parts select. In the meantime I put a temporary one feed valve on hot water feed line so I could have access to hot water in kitchen while I waited for parts wich were here in a couple of days. Put it all back and it runs fine. Thank for your help

I unscrewed the check valve, tipped the dishwasher on its face, and removed the asembly below it. Then replaced the valve flapper, cleaned out the assembly (broken champagne glass and udder nasties) then put it back the way I found it.
Then I put the new check valve on, and started the dishwasher up.

10 screws and $30 worth of parts saved me 400 bones for buying a new dishwasher.


If you have sanding water in your dishwasher check these two parts.....that check valve is the culpret.

First of all the part I ordered came a lot sooner than expected.
I thought it would take 5 to 10 days.
I ordered it on a Tuesday and it was at my door on Thursday.
The part was difficult to take off as this was the first time I attempted this.
When the new part came, I saw that I went to too much trouble to take the old one off.
It was installed in about 40 minutes and we were off and running.

Replaced with a new rinse aid fill cap.

Once the new motor and pump kit arrived. I removed the dishwasher, turned it upside down and replaced the motor and pump with the new one per the directions. Difficulty came in feeding the electrical wire/plug back through the cabinets. Once done, turned on the dishwasher, filled the tub, then manually moved the dial to drian. The water still would not drain from the tub. I searched further for the problem. Here it is; Found the air gap tube was plugged with food. Once I removed, cleaned and reinstalled the air gap, the tub drained fast and everything works great. So, I hope you folks put this up in your troubleshooting section for others to check before buying a pump and motor kit. If you had, I would have been able to check out the air gap, clean it out first before spending $140.00 for a pump and motor kit I didn't need. Anyway, lessons learned..Jeff

Replaced all ordered parts.

Turn off water .Remove 4 screws holding lower front panels.Remove panels, valve is on left . Remove 2 screws that hold valve , slip valve up over clip. Using pliers slide clamp back, remove hose from valve.disconnect wire clip , unscrew from water fill line. Install new valve in the reverse order

Removed the dishwasher from the cabinet. Turned it on it's top side. Removed the exit hose from the pump with a nut driver and replaced the flapper. Reconnected the hose to the pump.

The leak was coming from the drain valve shaft and I found the tips to replace the seal from this website. I was able to reach everything without removing the dishwasher from the cabinet. Once I got the cam lifter off the old push on nut was corroded so it was easy to get off. The old seal was recessed so I used the point of an ice pick to gently pry it out. The new seal was easy to push in place but the push on nut was a bear. I saw other comments about using a deep socket to push it on but I didn't have one the right size. I was able to hold the end of the shaft with pliers and pushed the nut in place using a screwdriver. Ran a short cycle and no more leak. Thank goodness for this website. Found the part easily and the other written comments were very helpful.

Leaking at bottom of door edge - ordered new gaskets all around - no sense in replacing one at a time and paying extra shipping. Removed screws on the inside of the door panel and it lifted off easily. bottom corner of gasket was black and that is where some of the leaking was from. I replaced the door seal and ran the washer and it still leaked.... Pulled the washer out from the enclosure and it was quite wet back there - so I wanted to pull the washer to dry and clean things up - turned off power and water and remove screws at top edge that secure it to countertop. Insulation wrap was wet - Removed that and put it into the sun to dry - no sign of where water was leaking - reconnected water and power and ran a cycle with the washer pulled out - slowly leaking from top of washer where hose enters the top sprayer. Was easy to get to the sprayer - two little screws hold it in - removed the hose that feeds the sprayer and it was disintegrating - crumbly- I ordered the part and put it all back together and used a washer at the sprayer/hose junction to compress the fitting in hopes it would hold until the replacement came - it did. The replacement installed in 10 mins and did not need to disconect water or power. I would suggest replacing this hose at the same time you replace door seals based on condition of my hose.

turn circuit breaker off

Remove 7 screws holding internal panel on door
pull panel up and off,be careful to clear door handle through slot on front. Put a weight of about 8 pounds on the door to hold it open

Remove six screws holding the circuit board, and the small black switch assembly and the pop the control board out. Swap electrical connections from old to new board. Reassemble in reverse
screws should be tightened with fingers on screwdriver only (metal in plastic)

Clean up and collect kiss from spouse

Received part, removed lower panel and shut water and power off to appliance. Used flash light to see under dishwasher, removed the two screws that held part in place. Loosed clamp that held the water tube in place to part. Placed towel down to catch water. Pulled the line out so I could get to the nut that is attached to inlet part. Unhooked the plug after all water was gotten up. The main knuckle that's attached to the pump was on so tight that I took it to my local gas station for an mechanic to unscrew it for me....I have arthritis in my hands. Station is only two mins from me and wasn't a problem for them to do for me. Came back put fresh Teflon tape on joint and reattached it to new part. Attached all hoses and clamps, plugged electrical prongs back in and attached bracket back to body of dishwasher. Turned water on and checked for leaks. Turned power back on and ran a cycle of dishes to wash....all went well. If the knuckle was on so tight the job would have only taken about 40 min at best.

Removed 4 screws, took off basket covering, put new part in one turn, then replaced covering. Plumber had come out, I watched what he did, he had to order part and come back. I asked how much he didn't know but said cheaper than buying a new dishwasher. When he left I started calling around about the little plastic part that I needed. Part was $15.50. They called and said it would be $110.00. Needless to say I called them out and ordered the part myself and put it in. Took me like 6 minutes and cost $21.69. I was so mad about this situation that I even got my service call money back that I had already paid.

First I removed the four screws that secure the dishwasher to the underside of the countertop. Then I removed the four screws from the front cover at the toespace. Next I used an adjustable wrench to turn the feet to lower the unit enough to slide it out of the compartment. I unplugged the dishwasher and turned it on its side in order to access the hose chamber. I used a pliers to loosen the clamps at each end of the hose chamber and removed the the damaged item. Next I slid the ends of the new part into place and used the pliers to reposition the clamps. Finally I returned the dishwasher to an upright position, slid it back into the compartment, adjusted the feet to raise it to the proper height, put the toespace cover back on, secured the top of the unit to the underside of the countertop and I was good to go. No more water leakage.

Old baffles lift out and new ones installed - very easy