GDT625PGJ5WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rickey from POPLAR BLUFF, MO
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower spray arm broke
Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from ABINGDON, MD
- Parts Used:
- WD15X26140, WD01X22514
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Valve was leaking
Took old valve assembly off and replaced with new assenbly
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from BENNINGTON, VT
- Parts Used:
- WD15X26140
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No water
just bolted on the new one and hooked up the hose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jedrino from HAWTHORNE, CA
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Thumping Sound during the WashRinse cycles
Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from WINCHESTER, TN
- Parts Used:
- WD19X25187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Water would not drain.
Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rhonda from College Corner, OH
- Parts Used:
- WD21X24901C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Dishwasher would not power up
This dishwasher started to not want to start about 1 year ago but on several attempts to start the dishwasher it would power up or start. On Christmas Eve 2021 I did a load of dishes and from that point on the dishwasher would not power up. Got on line and did some troubleshooting and felt the Control Panel was the problem. Ordered the replacement part from this website, the part arrived around January 1, 2022. Installed the new Control Panel yesterday and my dishwasher is now working great again. Thank you for the ability or order and fix my dishwasher
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Mesquite, TX
- Parts Used:
- WD21X31902C
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
No illumination on controls and no response from buttons
Shut off power to the unit, removed the front lower trim and under counter screws, then I disconnected the wiring from under the door leading to the UI at the top edge of the door. Removed the front door, separated and disassembled the outer door cover, I then removed the UI control board from its housing and the clear cover and reassembled the parts in reverse order and turned the power back on. FOLLOW the included instructions on connecting the pins on the new UI by cross reference the model number.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from ELK, WA
- Parts Used:
- WD21X24901C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
It didn’t work I had to wash dish’s by hand
The repair went very well, I watched a video on how to fix it on utube for this model the board from partselect was a OEM and fit perfectly. If I ever have an appliance problem partselct will be the number 1 on my list to call. I have told most of my friends about them and how great they are to deal with. They rate eleven stars.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CROSSVILLE, TN
- Parts Used:
- WD13X10071, WD21X10490
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Dishwasher won't start.
Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from NAPLES, FL
- Parts Used:
- WD21X24901C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Dishwasher would not start. No lights on select board
After reading the manual that came with my dishwasher, 5 years ago, it states if the green LED is on steady, change the machine control board. PartsSelect sent the bd within a week. I replace the board but the result was the same (steady green LED); Contacting PartsSelect, they gave me a return label and shipped another control board. Unfortunately the second control board had the same outcome. PartsSelect send another return label and I returned both machine control boards. I contacted GE and am having a service man (from GE) come and fix it. The manual for this dishwasher must be in error!! PartsSelect has been fantastic in understanding this and allowing me to return the bds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from NASHVILLE, TN
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dishwasher door sensor/ mother board
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from MONMOUTH BCH, NJ
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Control board would not properly work and light up
Followed a u-tube video to remove dish wash door assembly to get to the control board . Not too hard if you are mechanically inclined.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lori from ALLENDALE, MI
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The control panel went out
READ THE INSTRUCTIONS THAT COME WITH THE PART! After taking the dishwasher apart and installing the new part...it still didn't work. Then we read the instructions that came with the part. There are different settings on the part depending on your model of dishwasher. We removed the part, set it to our dishwasher, and it works perfectly. The job could have been quicker if the instructions had been read first.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from NEOSHO, MO
- Parts Used:
- WD21X31902C
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
No power to the control panel
Removed the door to get to the UI control panel. Followed the instructions to set the jumpers to my particular model and put it back together. Fixed the issue and worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Rio Verde, AZ
- Parts Used:
- WD22X33499
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lower arm spray had hole melted in it
Simply put it on and twist it to lock in place. Took all of 3 seconds
Was this instruction helpful to you?
Thank you for voting!