GDT545PSJ5SS General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from Magnolia, TX
- Parts Used:
- WD21X31910
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
We were not getting power to the control panel
The repair made it necessary to remove the door of the dishwasher. Removing the door seemed to be a daunting task, but after watching a YouTube video I made myself aware of the necessary steps to complete the task.
- After turning off the power to the dishwasher, I removed the kickplate panel, this gave access the wiring going to the defective board, which I unplugged.
- Removed the screws securing the dishwasher to the counter, these are located at the top of the machine and are accessible by opening the dishwasher door.
- Pull the dishwasher forward a few inches.
- On each side of the door is a spring loaded device that holds the door from falling open when not latched. They can be identified as white plastic items with a cable connected to them. Once removed take care to not allow the door to fall open, instead, when opened slightly raise the door off the unit.
- Lay the door on the floor.
- There are three sheetmetal screws on each side of the door, using your nut driver remove these screws. They secure outside of the door to the inner door.
- Stand the door up on the floor and raise the outer door panel, there are several plastic clips on each side the slide into slots on the inner door panel. I found it a little difficult to separate the panels, but with gentle persuasion they came apart.
- Lay the inner panel on the floor with the exposed electrical components facing up.
- At the top of the inner panel is a black plastic cover protecting the electronic components, this where the control panel lives.
- Remove the sheetmetal screws that secures this plastic cover.
- There are two wiring harnesses, remove them.
- The defective component can be lifted out.
- Install the new control panel.
- Reassemble.
- After turning off the power to the dishwasher, I removed the kickplate panel, this gave access the wiring going to the defective board, which I unplugged.
- Removed the screws securing the dishwasher to the counter, these are located at the top of the machine and are accessible by opening the dishwasher door.
- Pull the dishwasher forward a few inches.
- On each side of the door is a spring loaded device that holds the door from falling open when not latched. They can be identified as white plastic items with a cable connected to them. Once removed take care to not allow the door to fall open, instead, when opened slightly raise the door off the unit.
- Lay the door on the floor.
- There are three sheetmetal screws on each side of the door, using your nut driver remove these screws. They secure outside of the door to the inner door.
- Stand the door up on the floor and raise the outer door panel, there are several plastic clips on each side the slide into slots on the inner door panel. I found it a little difficult to separate the panels, but with gentle persuasion they came apart.
- Lay the inner panel on the floor with the exposed electrical components facing up.
- At the top of the inner panel is a black plastic cover protecting the electronic components, this where the control panel lives.
- Remove the sheetmetal screws that secures this plastic cover.
- There are two wiring harnesses, remove them.
- The defective component can be lifted out.
- Install the new control panel.
- Reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from BEND, OR
- Parts Used:
- WD28X22621
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The blue colored silverware holders had broken pegs at the ends.
Removed the old assembly and put the new one in. Took about 15 seconds. Perfect replacement. This assembly is the complete basket. The color of the blue silverware holders changed to grey which is not an issue at all unless that was the reason you bought this dishwasher in the first place. ;-)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADENTON, FL
- Parts Used:
- WD21X10490
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not shut, machine would not run.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PRAVEEN from MONROE TWP, NJ
- Parts Used:
- WD28X35779
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rusty DW Baskets
the part is OEM and fits like a glove. No worries. There is a minor variation in design and is not like for like design but fits exactly per specs and works. I have been looking for this part for years now. Thank you for PS for maintaining the inventory.
PS12743260Manufacturer Part Number WD28X26099
PS12743260Manufacturer Part Number WD28X26099
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauran from MYRTLE CREEK, OR
- Parts Used:
- WD21X24901C
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Need New Board
Replaced old One,Watched a Clap on You Tub !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francesca from PALM COAST, FL
- Parts Used:
- WD28X35779
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rusty upper rack
I simply followed the video instructions and replaced the rack myself, no tools required. Easy peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Plainfield, IL
- Parts Used:
- WD08X21894
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Worn bottom door seal
Easy repair, googled a how-to video and I was surprised how well i was able to follow instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from CONCORD, NH
- Parts Used:
- WD05X30818
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Dishwasher was not heating up to dry
Took out the old heating assembly and installed the new one
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
this did not solve my problem and I ended up buying a new dishwasher and returned the part
Spent as much in shipping to get the part and return it as the part cost itself
Next time I will just replace the dishwasher in the first place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from OXNARD, CA
- Parts Used:
- WD08X21894
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Bottom door seal broken and leaking
Unplug power to the dish washer.
Remove 2 kick plate screws to remove kick plate
Remove 2 screws that hold DW to underside of countertop
Slide out dishwasher enough to access the cables on each side at bottom of door.
With door closed, use plyers to lift the cable (one on each side) off the retaining stub.
Unplug door wiring connector.
Open door and slide door off the hinges.
Slide old seal out and insert new seal.
Reverse to reassemble
Remove 2 kick plate screws to remove kick plate
Remove 2 screws that hold DW to underside of countertop
Slide out dishwasher enough to access the cables on each side at bottom of door.
With door closed, use plyers to lift the cable (one on each side) off the retaining stub.
Unplug door wiring connector.
Open door and slide door off the hinges.
Slide old seal out and insert new seal.
Reverse to reassemble
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from BURKE, VA
- Parts Used:
- WD08X21894
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Dishwasher Leaking at bottom when running
To remove/install gasket one has to remove a Door Hinge Arm on one side. Then you can easy remove old gasket and replace. Please follow these steps when removing a hinge: https://www.youtube.com/watch?v=hTpe1dedyr8
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from PLYMOUTH, MA
- Parts Used:
- WD15X26140
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench (Adjustable)
Dishwasher not operating. Would fill, not operate, then drain.
Performed all checks on youtube...water coming in, course and fine filter cleaned, drain pump working (heard it come on and no water present and cycle end). Swapped water inlet valve bc it was the cheapest poss fix $19. No luck. Ordered circulation pump and motherboard. Swapped pump, very easy with machine out and turned on its back. Temp reinstall and ops checked good. Contacted Partselect for return slip, emailed immediately and sent thru post office.
Was this instruction helpful to you?
Thank you for voting!