GDF620HGJ5BB General Electric Dishwasher - Instructions

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.

Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.

Make sure power to dishwasher is off. Unscrew from counter. Pull dishwasher out enough to expose pulleys that hold the door in place. Remove lower panel and insulation. Unplug door jack from main panel underneath. Loosen pulleys on each side and remove door. Take a 1/4 in socket and remove the bolt on the upper side of the hook on each side, then remove the screws on the outer side panel on each side. Now slide the inner door panel up (push the top and pull the bottom), which will release the hooks on each side. Turn over the inner panel and remove the four screws that hold the interface control panel in place. Unplug the two jacks and remove the panel. Now take a small flat-head screwdriver to remove the clear cover. Remove the control panel. Make sure you set the junction as prescribed with the instructions that come with the new control panel. MIND YOU- YOU HAVE TO REMOVE THE JUNCTIONS (TAKE EACH ONE OUT) AND RESET THEM ON THE PRONGS IN THE ORDER AS PRESCRIBED. Replace the control panel, replace the clear cover, insert it back in place, plug in jacks and replace screws. Turn inner panel over and line up side where the hooks lock. replace all screws and bolts. Replace door on dishwasher, plug in jack to main panel, attach pulleys to door. Replace insulation and front panel to bottom of dishwasher. Push dishwasher back in place. Replace screws that hold dishwasher to counter. Turn main power back on and VOILA!!

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

A quick twist of the locking nut

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

It took longer to uninstall and reinstall the dishwasher than it did to change out the part

Simply unscrewed the old damaged arm and screwed the new one on, took less than a minute

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

The old gasket pulled right out with no tools needed,
The new gasket went in the same way.

Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.

Next Steps:
When the bottom gasket gets here I will replace that and it should be as good as new.