GDF510PGJ5BB General Electric Dishwasher - Instructions

Performed all checks on youtube...water coming in, course and fine filter cleaned, drain pump working (heard it come on and no water present and cycle end). Swapped water inlet valve bc it was the cheapest poss fix $19. No luck. Ordered circulation pump and motherboard. Swapped pump, very easy with machine out and turned on its back. Temp reinstall and ops checked good. Contacted Partselect for return slip, emailed immediately and sent thru post office.

I replaced the Flood Switch Part Number: WD21X10519.
I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.

Upper rack I had to reuse the old power was assembly but it just snaps into place. Lower rack literally just place on roller track and it was done. No tools required. Extremely satisfied with my purchase. 10/10 recommend!!

I simply followed the video instructions and replaced the rack myself, no tools required. Easy peasy

The pump went out after a few months of very loud noise during the drain cycle and then one day no drain or noise. A bit of research shows that this pump goes out frequently on this model so I ordered a new pump after inspecting the old pump for a clog or snag on the rotors.

The Install:
After removing the dishwasher from it's installed location and turning it on it's side (unplug water and electric of course), I was able to remove the pump from the two lines that connected it to the dishwasher and the drain line. I also had to unplug the pump from an electric connection to the dishwasher. Swapping out the new pump was the same but in reverse. Not a hard install, only simple tools required.

One note, my electric connection to the dish washer was different on this model pump since they changed the original part but there is an adapter included with this part so make sure it is in the box and fits before beginning.

Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.

My granddaughter's fian'ce actially replaced the pump.
He pulled the dishwasher out, tipped it over and quickly and easily replaced the pump.
I had already snapped the converter on to the pump so it was ready to hook up. I had read previous messages that this part had a converter.
After putting the washer back in place we set it on a light wash to test it.
It went very well.

The Mid Spray Arm Assembly was not spinning due to a dish that was in placed the dishwasher that was too high and hitting the arm. When it spun until it broke the center shaft. Replacement was easy. After removing power I pulled the upper tray out and removed the Conduit Mid Tiered Assembly by unsnapping it from the tray. I twisted off the broken spindle of the damaged arm assembly from the Conduit Mid Tiered Assembly and inserted the new arm and gently pushed it until it snapped into the Mid Tiered Assembly. Reinstalled the assembled parts by snapping into the tray making sure it was centered.

took out old and replaced with new

A quick twist of the locking nut

It was a simple as: attach and done!
There is a ring on the part that tightens clockwise to the nipple that sprays out the water that it rests on. Twist clockwise and you are done!
It is a mystery how it was unattached to begin with but not a problem in the end, it was easy to fix!

Thanks for sending genuine GE parts!

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

Since I have granite countertops, unscrewed 2 screws on each side of cabinet. Unscrewed the toe plate, unplugged the wire connector, and disconnected the cable
from the door which was held by tie wraps. Pulled out dishwasher about a foot. Unhooked the spring cable to the door, lifted the door out and placed it on a spare table. With door face down on a towel, I unscrewed the screws at the bottom to release the latches, then unscrew the screws that hold the door locked in place. Turned the door on its back face up, wedged a flathead driver to release the settings display, from the body of the door. Separated the 2 panels replaced the foam rubber vent seal. Placed the face face down, reconnected both pieces of the door together pushing down. Rescrewed the bottom to lock the 2 pieces together reinsert the hinges, screwed them in with nutdriver1/4". Grabbed the old gasket, replaced it with new one, sliding it into the groove on the bottom inside of door. Reattached the door to the washer, rehooked the cables to the door, retired with zip ties the cable to the underside of door, reinstalled the wire connector, and re screwed the toe plate. Pushed the dishwasher, leveled, rescrewed into cabinet. Replaced the tub gasket.

Super easy repair, just removed the old latch and replaced it with the new one.

Replaced gasket with a new one before further problems occurred. Got to get it in but it was relatively easy to place and snap in just make sure it fits on the right place where gasket inside meets ridges on door so it will be on properly for proper fit.