DDT595SBL3TS General Electric Dishwasher - Instructions

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

The installation is fairly straightforward, basically one plug in electrical connection and two plumbing connections. The smaller of the two plumbing connections can be tricky because of the hose clamp... The original clamps are one time use crimp style. The replacements are standard hose clamps, which means the section where the tension mechanism is, is a bit wider than the clamp itself... This can cause the rubber collar on the dishwasher to slide off/separate from the pump part itself when tightening the hose clamp. If you are careful and align things just right, it will work like a charm. The best advice I have is to take your time and make sure the connections are snug without being too tight, otherwise it could leak and/or something else could break.

I watched a step by step video provided on the Fix It app. Easy to follow directions and only took minutes to tear apart and put back together. Didn't even require help from my husband. Although the latch and striker were not the problem, contacted parts select and they then recommended the electronic control board, they ordered it, had it shipped to me within a few days, another really easy fix I did using the You tube video. Fixed the problem lickety-split. I will never go without my fix it app. Entered all my appliances. Sure beats spending hundreds on appliance repairmen! Thank you Parts Select!

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

Dishwasher is under 2yrs old and suddenly failed to drain due to the drain pump not working. I read the reviews on how easy it was to change and went ahead and purchased one. After removing the screw from the appliance bracket under the counter and the two screws from the base plate, it was easy to pull the dishwasher from under the counter and away to flip to its side. I would recommend draining the drain hose first and making sure no water is in the tub. Keep a towel nearby. Removing the drain pump was simple. I needed a nose tip pliers to remove one of the hose clamps and a screwdriver for the other clamp. Once the pump was removed, I opened the old pump by twisting the top part while pressing the tabs to remove upper housing. There was a broken piece of glass that had wedged itself in the mechanism which prevented the pump from working. I wish I had checked that first, before purchasing a new drain pump. I kept the old pump as a backup for the future. It took no more than 20 minutes to get the pump replaced and the dishwasher back in place. Dishwasher drains just as new. By the way, costed under $100 with delivery. An appliance repair company wanted $250!!
Not the first time PartSelect saved me money and won’t be my last!

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

My son did the repair, I ordered both latch and striker, only needed the latch...only took him a few minutes to remove the old and install the new and works just fine

Shut off power at breaker, remove two screws anchoring DW to counter top . Slide DW out far enough to access door latch, disconnect electrical wiring plug, remove two Phillips head screws, install new door latch, repeat installation in reverse order.

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

This dishwasher started to not want to start about 1 year ago but on several attempts to start the dishwasher it would power up or start. On Christmas Eve 2021 I did a load of dishes and from that point on the dishwasher would not power up. Got on line and did some troubleshooting and felt the Control Panel was the problem. Ordered the replacement part from this website, the part arrived around January 1, 2022. Installed the new Control Panel yesterday and my dishwasher is now working great again. Thank you for the ability or order and fix my dishwasher

Unplugged power.
Shut off water supply.
Remove the kick panel.
Unscrewed dishwasher from under cabinet and side screws. lower feet to reduce tension.
As you slide the dishwasher out, be sure all lines (Drain, water supply, electric are free to move with dishwasher.
I was able to hold the dishwasher at an angle to easily get to the valve. After removing the the valve, i screwed the new valve back into place. I removed the Line between the valve and Dishwasher. Putting the line on the new valve. I removed the water supply line from the old valve and installed it on the new valve.
Placed the dishwater back in place and screed it back in. I ran the cycles. everything works!
I replace the kickpaner a couple of hours later. Check to make sure there were now leaks.

This is a replacement that is straightforward but a bit mechanical. For an experienced engineer it was no problem but for the common household this is a repair best left to the pros. Fixed the issue no problem and the dishwasher is working perfectly now.

It was relatively easy to fix. I unscrewed the mounting screws from the cabinet, slide the dishwasher out to access the pump under the dishwasher, I did raise the dishwasher on the left side and steadied with a stool to make access to the pump fitting easier. Then I loosed both clamps at the ends of the hose ie. from the dishwasher pump and the connection to the sink drain line, pulled the clamp off of the end that connects to the pump and placed it on the new hose connection, I removed the old hose, connected the new one and tightened the drain line connections. I placed the hose in the hose holders on the side of the dishwasher slid the dishwasher back into place and secured it in place with the mounting screws.

Repair was straightforward. You can change water inlet on this model from underneath in bottom from, although it is a little tight