DDT595SBL2TS General Electric Dishwasher - Instructions

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

A noisy dishwasher and water coming from underneath was being caused by a torn hose that is factory connected to the diverter. It was a little difficult to see at first as the hose sits slightly kinked when in it's normal position. Access to the diverter involves removal of the circulation pump. I ordered a new diverter which comes with metal screw on clamps. The main difficulty in installing is the positioning and alignment of the diverter and pump. My first effort resulted in a ripping of the attached diverter hose as I attempted to secure. I ordered another diverter. This time I used a lubricant to allow movement of the connecting hoses and made sure to not overtighten the clamps. I used a small mirror to make sure that the various hoses sat properly. Alignment took a bit of time. I then gently tightened the hoses. I ran the dishwasher, and found a leak, meaning that I needed to tighten these clamps a bit more. This is a doable repair that needs patience. The dishwasher is now very quiet and runs great!

Took old valve assembly off and replaced with new assenbly

just bolted on the new one and hooked up the hose

the design of this part is easy to break when closing the top rack.

there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher

the part broke when closing the rack [a dish too tall hit it]

it took less than 5 minutes to replace as the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel

Replaced old gasket with new one. More difficult than expected, because new gasket was much stiffer than old one. Also, the yellow centering spot on gasket (to line up with top latch) was nearly impossible to see. Unfortunately, this did not solve the problem for me, so money was wasted. Bought new dishwasher.

Opened the door, put arm on bottom, slid in and twisted. Very, very easy. The right part means a lot. Thank you very much. “ Ol Stump”.

Chances are your Lower spray arm is worn or jets are off. Replacing this part is very easy. Grab the base of the lower spray arm, twist and pull straight up. Place the new one in and twist lock in place. Repair complete!

Started by removing dishwasher, including disconnecting power, water and drain line. Then turned washer on back. Electrical connector to old wash pump was a little tricky to remove as the release tab isn’t straightforward, I used a tiny screwdriver and jiggled it around till it came loose. The factory hose clamps (2) are crimped on, but if you can find the tail end you can work them loose with a screwdriver by prying the tail up from the body of the clamp. Once you have the electrical connector and the two clamps removed, the pump comes of easily with a twisting motion. The new wash motor came with new clamps (2 extra). When sliding the rubber boots on the new pump in place, it will require a twisting motion to position it correctly, make sure (I didn’t and had to go through the whole process twice) that the rubber boot is not folded under on the bottom where it’s hard to see. Tighten clamps carefully and don’t over tighten. Plug in electrical connector and you’re ready to reinstall dishwasher.

This dishwasher started to not want to start about 1 year ago but on several attempts to start the dishwasher it would power up or start. On Christmas Eve 2021 I did a load of dishes and from that point on the dishwasher would not power up. Got on line and did some troubleshooting and felt the Control Panel was the problem. Ordered the replacement part from this website, the part arrived around January 1, 2022. Installed the new Control Panel yesterday and my dishwasher is now working great again. Thank you for the ability or order and fix my dishwasher

Unhook water line . Turn off power to dishwasher. Remove dishwasher from under counter. Lay it on its back. Loosen clamps on drain pump and remove pump. Install new drain pump and tighten clamps. Be sure to put hanger in the hole on the pump. Very easy job. Reinstall water line and put dishwasher back under counter. Turn on power to dishwasher. Go to go.

The repair went very well, I watched a video on how to fix it on utube for this model the board from partselect was a OEM and fit perfectly. If I ever have an appliance problem partselct will be the number 1 on my list to call. I have told most of my friends about them and how great they are to deal with. They rate eleven stars.

Nightmare!!! The Striker latch did not pop out with a screwdriver as it was supposed to. The whole dishwasher needs to be disconnected and pulled out, then front door removed and totally disassembled to remove the screw to replace the striker latch. lots of work to replace a striker latch. Bad design!

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

After reading the manual that came with my dishwasher, 5 years ago, it states if the green LED is on steady, change the machine control board. PartsSelect sent the bd within a week. I replace the board but the result was the same (steady green LED); Contacting PartsSelect, they gave me a return label and shipped another control board. Unfortunately the second control board had the same outcome. PartsSelect send another return label and I returned both machine control boards. I contacted GE and am having a service man (from GE) come and fix it. The manual for this dishwasher must be in error!! PartsSelect has been fantastic in understanding this and allowing me to return the bds.