DDT595SBL2TS General Electric Dishwasher - Instructions

Didn't actually do the compete repair but got close. Pulled out dishwasher, disconnected and checked continuity on the existing heating element (about 16 ohms) the new element was also about 16 ohms. This indicates they both were working fine and no need for replacement. Next step would have been to swap the elements would have been simple. Tried to replace main board as well, still not the issue so giving up and replacing the dishwasher. It wasn't the high temp cut off thermostat either incidentally and no error codes in maintenance mode. Check continuity of your existing element before ordering to save aggravation.

Open the washer, remove the bottom dish rack, then twist off the bottom water sprayer. Use a screwdriver to remove the mounting/ stabilizing screws so you can slide out the dishwasher. Close the dishwasher and slide it out. Underneath at the back there are two wires powering the drying element, carefully remove them. Use an adjustable wrench to remove the two plastic mounting nuts for the drying element. Open the washer and remove the old drying element, and insert the new element. Reassemble the dishwasher in the reverse order if disassembly.

1. Turn off breaker supplying power to dishwasher in electrical panel
2. Open dishwasher door
3. Unscrew the screws that secure the dishwasher to the counter.
4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch.
5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside.
6. Remove old door latch.
7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in.
8. Plug wire harness into new door latch.
9. Re-align dishwasher and re-secure to counter in previous position.
10. Test latch to make sure it closes properly.
11. Turn on breaker in electrical panel.
The dishwasher should now function properly.

repair under warranty for Home Depot. Ordered new controller, new sump manifold, new piranh clamp kit, new diverter passive main assy, installation took 6 months. Could not finish as GE had changed the diverter to a new design with the same part number that the repairman had no knowledge of and there is no part available for the same configuration of the one that went bad, after I called GE tech line they were not aware of updates. Giving me the same numbers. The new design works if you order a new conduit main. As the old one in the dishwasher will not connect to the new Diverter. New deverter no. WD19X25278 and the new main conduit is the same as the old configuration no.WD12X21681 . The repair people and parts people are not yet aware of the design change and availability of parts, as most are out of stock and no updated pictures of the new design. Repair warranty washed their hands of this and Home Depot after 6 months gave me credit of my full price I bought this for 3 yrs ago. Repairing myself and sell.

When the part arrived, I was pretty sure it was the wrong part. The replacement part had an LED on it -- a box that stuck up about an inch above the circuit board. My dishwasher did not have an LED readout and I was pretty sure the LED would not fit in the space that was available. I was reluctant to take the dishwasher apart until I had the right part. The people at Part Select were helpful and together we looked at the schematic which did, indeed, seem to show a box sticking up from the circuit board. A YouTube video showed me how to take the door off its hinges, unscrew 4 screws and slide the inside of the door upwards. The circuit board went in fairly easily. There was space for the LED (even though it still doesn't show through the top) and now the lights work.

Followed directions available on YouTube and the written instructions that came with the part. I made the repair more complicated than necessary as I did not notice that the jumpers come attached only to ONE pin out of the box. I took two tries to get the jumper settings right.

Replaced transition piece, gasket, and vent cover. The root cause problem is that the factory installed gasket was too thick and would not allow sufficient thread engagement. The replacement gasket was about 25% thinner and worked perfectly.

We bought this GE dishwasher new. After 9 months, we started noticing the dishes were not cleaning well. Eventually, the machine just filled up with water and drained. The washing arms didn't work. I replaced fill valve, but that didn't solve it. A GE Tech ran a diagnostic and informed us the pump motor was bad. It was off warranty and repairs would be $300. However, he noted it was easy to do on my own. Two pipe clamps. The part from PartsSelect was 40% less than ordering from GE and was a GE part. Replacement took half an hour and that includes getting it wrong once (one connection leaked due to a bad job attaching the pipe clamp). Works like a champ now.

I watched the video on how to replace the parts and it was very easy. Unplug the power cord, remove the kick plate and insulation. Remove the small square metal cover, remove the 2 screws that hold the control board plate. Unplug the wires, put the control board plate on the counter and replace the board. Then put everything back in the order that you removed it. Plug in the power cord. Very easy to fix. I ordered the door latch but didn't need it so I will just keep it as a spare. It took me less than 45 minutes to replace the part. The problem was the control board. Parts select saved me about 400.00. Thanks, John.

Took old valve assembly off and replaced with new assenbly

just bolted on the new one and hooked up the hose

Repair went fine, getting the right pump was the problem. I started with my local appliance parts house, they ordered part came in 3 days. Upon picking it up I noticed that the pump was shaped slightly different and the electrical hook up was totally different. Asking the parts guy what happened he said they must have sent the wrong pump. Returned it for credit and ordered it again. Four days later the same exact thing occurs. Parts guy credits my account and says better go directly to GE. Wait 10 days for GE, for this part and once again same odd looking pump with wrong electrical plug. My son who is a welder by trade asks me if there is a packet of parts in carton and yes there is. He says that perhaps there is a converter for the electrical. That was the solution no one told us that pump was universal and needed the adapter. Not even the 2 different tecks at first house. Perhaps that should be stated in the part would have saved us tons of time. Thanks D

I checked all the drain lines and filter for blockage. All looked good. I unplugged the unit and unscrewed the two screws adhereing the dishwasker to the counter. I shopvacced the water out of the bottom of the unit, slid it out, and carefully placed it on its back to access the pump. I unplugged the power to the pump, removed the intake and outake ring fasteners. Carefully removed the pump and inserted the new part, mopping up water as I went. Replace the rings, plugged in power to the pump, righted the unit and put it back. Replaced filter with the one that came with the kit.

Replaced heating element. This was the path of least resistance but the problem persisted. I tried resetting the dishwasher but still nothing. My last resort is the circuit board. I checked the relays on the old board and they are fine so it must be something else on the circuit board. The dishwasher is not really that old (4 years) and everything else is fine. Just ordered the board so I really hope this fixes the problem.

I got lucky and found the diagnostic test instructions tucked inside the washer under the kick plate. From there I ran the tests on each component until I narrowed it down to the pump. The pump cost me less than local dealers. The install went well. Watched the online videos to make sure I was doing it right. Was actually very easy and saved hundreds over a service call.