HSD3204X02WB General Electric Dishwasher - Instructions

Just put the part on.

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

Removed the lower rack and installed new wheels with clips

Took out interlock switch (two leads) and replaced with new one. As simple as that.

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

Simply screwed in new cap

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

Very simple. By hand, I unscrewed the old spray arm and screwed in the new one. One brief hangup. The old spray arm was very hard to unscrew. Rather than seeming to force it, I called the PartsSelect 800 number and got advice. The tech reassured me that all I had to to was unscrew it and put in new one. So I applied more force and old one came out. A breeze.

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.

Use screw driver for leveage, righty tighty, lefty loosie, easy as that, and thanks to Parts Select, ordered my part on Thursday by dinner time Friday had part, install no washing dishies by hand, Thanks guys

Brian Souza
Vacaville, CA

I just plugged in the model number and a screen came up that showed all the part numbers that made up the model. picked out the parts that we needed and ordered it and within 2 day we had the new basket that we needed for our dish washer.
the service and ease was better that going to the appliance store and picking up the basket.
I was very happy the the service.
Donald Brown

Went to repair parts on troubleshooting and found check valve assembly to be most common problem. Went to parts diagram to locate assembly and found it somewhat confusing as to exact location. Ordered part(s) on percentage as the problem. Received part next day (great)! Pulled dishwasher out and found I did NOT need to do so to replace check valve which is replaced without having to remove dishwasher. The gasket replacement was not necessary as it seals sump area from bottom of dishwasher and not the valve as it appears on the parts diagram. It took about 2 minutes to replace valve itself and it was the cause of the problem.

The video was extremely helpful. Removing the tabs was easy. However, we struggled with the re-insertion. They did not "snap" back in as easily as seen on video. We ended up using a pair of pliers to push pieces into slot. We did not use very much pressure for fear of breaking the plastic. However, after many tries, we were successful & it works perfectly. Perhaps a close-up of the "snapping in" part might help future installers.

I watched several YouTube videos on how to make the repair. It looked very easy but sometimes professionals, because they've done it before, don't point out small tips that would help a DIY homeowner. The latch goes easily into the inner door slot but there's nothing to hold it there. The videos show the inner and outer door being closed together without showing that you have to hold the latch in place while bringing the outer door up to meet the inner door. Any movement of the inner door makes the latch fall out. So I would say it took me 5 times longer to do this repair than it would if I was doing it again.