GSC3407P00WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- helmut from EAST KINGSTON, NH
- Parts Used:
- WD35X21038
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lower wheels kept falling off
Installed new lower rack wheel kit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from BROWNSTOWN, MI
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Axles had broken, leaving the tray falling down when pulled out too far.
Followed the very excellent instructions provided on website by Hotpoint/GE
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenda from NORMAN, OK
- Parts Used:
- WD12X10327
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Top rack of the dishwasher had broken rollers.
Installation was very easy! Rack works perfectly now. Only problem...bought four sets instead of 4 parts since the order form didn't say it included 4 in each pack.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from GRAND BLANC, MI
- Parts Used:
- WD35X21038
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
NONE
UNPACKED WHEELS AND CLIP. USING NEEDLE NOSE PLIERS SQUEEZED WHEEL TIP TO INSERT IN WHEEL. REMOVED OLD WHEELS AND RETAINER BY HAND. INSTALLED NEW WHEELS INSTALLED AND NEW RETAINERS
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenny from CARUTHERSVLLE, MO
- Parts Used:
- WD13X10003
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwasher would go on and off during operation
Took screws out of door panel to get to the latch and replaced old latch with new one. Super easy
Was this instruction helpful to you?
Thank you for voting!
door seal leaked,and the baffles
removed both corner baffles, also door gasket was bad, all parts were easy to order and install, the customer service was excellant with all my questions and concerns to get the right part and the parts arrived in just two days, thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Lebanon, OR
- Parts Used:
- WD28X265
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
First silverware basket had a hole in it.
Took out old one and put in the new one. Not hard at all. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from Southlake, TX
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A rack roller broke into pieces. The top tray didn't slide properly.
Removed the white end of the top track. Pulled off the remnants of the rack roller. Slide the rack roller wheel into the track and popped the other end on the top rack (looked at the other rack rollers to see how it fit.) After that, I put the end back on the track.... Note what is the top and what is the bottom of the track end. Realizing that there is a wider area on the track to slide part of the white track end through to get it on without much effort.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from TUCSON, AZ
- Parts Used:
- WD35X10346
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
threads were faulty
Removed the 7 screws from inner side of door; removed set screw from handle; removed inner door cover; pulled old part out; pushed new part in and Voila! Replaced all screws, no problem. Thanks for your great customer service!
Was this instruction helpful to you?
Thank you for voting!
The Drain shaft seal was leaking.
The solenoid and linkage was easy to disasemble, but getting the retainer (push on nut) off was difficult without removing the motor and pump. Once removed it was a snap. Getting the pump/motor back onto the pipes was near impossible from underneath. I had to remove the dishwasher from under the countertop to get it back correctly. I would reccomend doing this for this repair, as it made life a lot easier. Unwiring and removing the water supply line was not a problem either. WORKS AS GOOD AS NEW!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- forrest from stuart, FL
- Parts Used:
- WD08X10057
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace door gasket
from the information previous customers had written.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
it saved a lot of fustration and time
and best of all the dish washer does not leak.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nick from plainfield, IL
- Parts Used:
- WD18X214
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Simple fix
This is a very simple fix. The majority of work comes from getting the unit out of it's enclosed space so it can be worked on. Once the dishwasher is out in the open, lay it on it's side, and simply unscrew some metal clamps, pop out the bad part, replace it with the new, reattach the pieces and clamps, and start putting the unit back in place.
I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.
I'll be back to this site in the future if/when other parts on other appliances go bad.
I'm just happy I was able to actually find the part to begin with, and then to make the changes myself is a very rewarding feeling. Instead of missing time from work and shelling out $150+ to have an appliance repair man come out to do the work, I spent $20 for the part, and maybe an hour total to make the repairs.
I'll be back to this site in the future if/when other parts on other appliances go bad.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Francis from Oxnard, CA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Top rack was collapsing because 2 of 4 support rollers were coming apart.
First, end caps were removed from support rails to free the washer rack. This is a little tricky - flexible rear finger of cap is bent back, then rotated inboard to permit end cap to slide out. Ten top wash rack is rolled out of washer. Old roller support assembies are pried loose and then snapped off their clamp locations on the upper wash rack, one at a time. Then the new rollers are snapped on in same way, except no tools are required.
Two of the old rack rollers were clearly worn out from nearly 10 years of normal operation, where plastic shaft is a bearing surface.
Two of the old rack rollers were clearly worn out from nearly 10 years of normal operation, where plastic shaft is a bearing surface.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Belmont, CA
- Parts Used:
- WD12X10327
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper rack kept falling down
Removed the rack.
Removed the roller bar.
Removed the roller base from the rack.
Removed the roller from the roller bar.
Replaced in reverse order.
DONE.
Removed the roller bar.
Removed the roller base from the rack.
Removed the roller from the roller bar.
Replaced in reverse order.
DONE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frederick J from Howell, NJ
- Parts Used:
- WD12X10327
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rollers cracked and broke off the rack
Used a small flat head screw driver to remove the rail end covers (2) and removed the rack. Used my thumb to push the snap on roller assembly off the rack. The new rollers snap right back on the rack with just fing pressure. Re-installed the rack and then just pushed the rail end covers back on.
Very Simple Repair to a great machine. First problem in 13 years and still works great.
Very Simple Repair to a great machine. First problem in 13 years and still works great.
Was this instruction helpful to you?
Thank you for voting!