GSB9935VS119 General Electric Dishwasher - Instructions

Our older GE dishwasher was leaking water on the floor while running. After inspecting it while running I was able to determine that the water was coming from the seal around the motors shaft where it entered the pump. I then looked up the washers model number and ordered the impeller shaft seal kit. To my suprise the kit arrived the very next day! After disconnecting the power and water supplies from the dishwasher , I then removed it from the cabinet base and turned it over to gain easy access to the bottom. Using nothing more than a nut driver, adjustable wrench and a pair of pliers I was able to loosen the two compression clamps and two hose clamps that hold the pump to the bottom of the washers tub. I then removed the entire pump and took it to my work bench for the rest of the repair. Removing the plastic impeller strainer was the toughest part.. Lacking the proper spanner wrench, I had no tool that would lock onto the raised tabs to turn it loose with. I was able to position the tabs in the jaws of my workbench vise and giving the entire pump a little twist, It broke free and I was then able to unscrew the rest of the way it by hand.. The old dried up detergent made for a good adhesive, and after removal I cleaned the area completely so the new strainer would thread in easy. I installed the new parts in the kit as per the supplied instructions and re-installed the pump housing back on the dishwasher and put it all back in place. After running it several times not a drip was to be seen, and I was very pleased with the whole process. With the shipping it cost me just $25.00, and it saved me a expensive service call or maybe even the cost of buying a new machine. I would say that overall it was a easy repair but lacking the right tools, you may have some trouble removing the pumps plastic strainer screen as I did. I would highly recommend PartsSelect to anyone, and the entire experience was a good one for me.

This seems to be a simple repair, but the push on nut is difficult to remove. Ended up damaging the case, so I am going to buy another dishwasher. If you plan to repair, make sure you pull the unit out to have plenty of room to work with.

Pulled the lower left side end of the old door gasket out of door gasket retaining slot and slowly and evenly continued to work my way around the door pulling the door gasket out of the retaining slot until I reached the end. I installed the new gasket into retaining the retaining slot beginning on lower left side and then slowly and evenly working my way around the door inserting the new gasket into the retaining slot. I was careful to make sure the two cutout portions of the new gasket's retaining edge were correctly positioned in the lower corners of the door.

As suggested. Pull washer, remove screws from top and replace with new part. Very simple and easy if you follow steps furnished by this site.

remove water connection; shut off circuit breaker ; follow the suplied directions; reassemble washer . job done - leak gone. Wife happy.

Very simple repair: assemble the wheel/clip assembly. Attach to lower dish rack.

I was very happy with the fast delivery by PartSelect.

did it by hand, carefully flair out the plastic piece only enough to slide it into the metal rail.

took off the end clip, pulled the old wheel off and unclipped the bracket from the rack, then clipped the new assembly on...Simple!

I removed the broken lower spray arm tower using a scew driver and snapped in the replacement part not needing any tools.

and there was not supposed to be so I checked the drain and it was clean and I found a part in the back that looked like it was damaged from use and it was so I got a new part and changed it and that fixed the problem. I removed the screen from the bottom rear inside the cabinet that covers the nut and piston and I changed the part and that fixed the problem . Now no water stays in the bottom when the cycle is done.

Based on what I read from other people and partselect, it was fairly easy to ascertain what was wrong. I removed the solonoid valve by removing the two screws that held in place. Had to clean up the solonoid valve rod due to water leaking into it by running it on a wire brush. Pulled out the stop nut and old seal and replaced it with the new seal. Could not get the new stop nut on but it does not seem to move so let it go. Have to say that reading all the comments certainly helped me with the repair. Additionally, ordered parts by email at 10:30 in the morning and receiving them the very next day. Could not believe they were delivered so quickly.

Removed screws on the drain pump filter screens at the back of the dishwasher, unscrewed the check valve, screwed in the replacement unit, and re-affixed the filter screens.

I lived with the drain problem for 6 months and reviewed on line trouble shooting which all pointed me to a pump or solenoid valve problem. I pulled the unit and disassembled everything before noticing that the rubber washer/stopper at the top of the check valve had erroded away and was not preventing water from pumping back into the cabinet when the drain pump kicked on. Always check the condition of this check valve first if you dishwasher is not draining properly. It was so easy once I found the bad part.

It turned out to be an easier job than I thought it was going to be. Of course, I was still a bit surprised it worked right and didn't leak once I was done.

I started by taking off the servo that opens up the drain valve. I didn't think I could take out and replace the shaft seal from this position so I took the whole motor and drain assembly out by loosening the sump and pump clamps. This allowed me to wiggle out the whole mechanism. One plug and a ground wire had to be undone but that was it. The Push On Nut was the worst part - pain to take off - worse to get a new one on. I wasn't sure (still not) if I could get it in the right place. Once I got everything back together and the servo mount on it seemed to hold the nut in the right place.

I tested it and yelled "it doesn't leak!" my wife promptly said "Yet!".

We have run the dishwasher twice - so far - no leaks!

I couldn't have done it with out PartSelect's prompt service, diagrams, and part photos. I don't want to fix any more appliances but if I have to PartSelect is where I'll come for parts and diagrams.

Removed old basket, put new one in. New basket fits but it is larger then the old one so it takes up more room leaving less room for dishes. My dishwasher is apartment size.

Service from PartsSelect was very prompt.

Repaired by watching the video provided on my computer by this site . This video was a life saver and covered every detail. My thanks to this site !!!