GSD1807K00WW General Electric Dishwasher - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- John from Frederick, MD
- Parts Used:
- WD12X10164, WD08X10048, WD01X10242, WD08X23648
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable)
Water gushed from the main conduit. Dishwasher is not 2 years old.
First the parts took forever to get here and then the new main conduit nut was defective just as the original from the factory was. It would not thread correctly and had to be wet then forced by hand until the skin ripped off my fingertips.
GE stands for "Good Enough"
GE stands for "Good Enough"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Miami, FL
- Parts Used:
- WD13X10028
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dishwater door would not open because handle was broken
The repair could not have been easier. I looked up the model and found a diagram showing all of the parts for the dishwasher. Other people had commented on similar problems, so it made sense that I needed to order a handle/latch assembly. I order it and selected standard shipping. The part arrived the next day in the mail. It took only a few minutes to install the part. I know nothing about dishwasher, but this website made into a professional repair tech!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from Erwinna, PA
- Parts Used:
- WD28X10215, WD12X10178
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Broken roller assembly
Removed broken assemby. Replaced with new part. Basket was an even swap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Pittsburgh, PA
- Parts Used:
- WD12X10168, WD12X10167
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My dishwasher filters were clogged by calcium scale
I just lifted out the old parts from the bottom of the dishwasher and replaced them with the new ones which seated securely with no problem. The extreme amount of calcium carbonate in the water in Barbados settles on anything that gets wet. We clean the parts in the dishwasher, tea kettle and any other device that gets hot water, about every six months but eventually the boiler scale clogs the works and, while I can boil the parts in vinegar to clean them, the new replacements are much better and more convenient.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lance from Beach Park, IL
- Parts Used:
- WD01X10242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Upper rack of dishwasher was not cleaning well.
We noticed spotting and just poor cleaning performance in the dw. It was particularly bad on the top rack. After removing the racks, it was clear that the gasket on the water fitting in the back of the dw-upper was about half gone. No tools were necessary. I just unscrewed the ring nut-gasket and replaced it with the new one. Finger-tight. If the old nut was stuck, a pair of pliers would have helped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dexter from Hempstead, NY
- Parts Used:
- WD18X10028, WD12X10164, WD01X10242, WD08X23648
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
hole in connectiing duct. causing leaking.
First I shut off water and unplugged pwr cord from washer.I then removed hose from connecting duct and remove connecting duct from washer. I then installed new duct and reattached hose to connecting duct. After installation I reattached water hose then plugged back in pwr cord.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EUGENE from CENTEREACH, NY
- Parts Used:
- WD28X10215
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dishwasher basket worn our and utensils slipped through bottom
1. open dishwasher, 2. roll out bottom dish rack, 3. remove old silverware basket, 4 place new basket in same spot old basket was in, 5. roll bottom dish rack back into dishwasher, 6. close dishwasher door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Meredith from New York, NY
- Parts Used:
- WD13X10028
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken latch
I found a few how to videos to describe how to replace the latch since nothing was listed here. First - turn off the power to the dishwasher from the fuse box. Open the dishwasher and unscrew the door until the front piece and the control panel come off (I think there were about 10 screws- some are different sizes, just take note what goes where). Then you'll need to disconnect the 4 wires from the broken latch, before you do this either label the actual wires with where they go or take a picture so you know exactly how to put it back together - there is very little information online to guide you if you forget and if you get it wrong the dishwasher won't work, which I learned the hard way. Unscrew the broken latch, and replace with the new latch. Reconnect the wires following your guide, and screw back on the door. Voila!
Was this instruction helpful to you?
Thank you for voting!