GSD5911D00BB General Electric Dishwasher - Instructions

Only getting "humming" sound from dishwasher. Although water had filled the dishwasher tub, pump/motor would not operate. After some research, figured the motor had siezed and I had to replace the pump/motor assembly as mentioned on this site. The kit came in a couple days and I reserved a Sunday afternoon for the repair which I had never done before. Hardest part of repair was unhooking and removing dishwasher from under counter and then getting it back in proper place. I would suggest providing some instruction within the repair instructions showing how the dishwasher is installed or how to remove it as I had never installed one so I was not quite sure what screws etc I needed to remove on the dishwasher itself to start to remove it? I was able to find the original installation instruction for the dishwasher and found that all you had to do was remove two screws from the inside top of the dishwasher which were securing it to the bottom side of the kitchen counter and then the whole thing just slides out. Once removed, turned dishwasher over to access bottom where pump/motor is located. After determining which diagram to use with the instructions, proceeded to replace the motor/pump assembly. It came out easily after wrestling with some corroded bolts/nuts and the existing pump inlet and outlet hose clamps. Mine were old and worthless and no new ones (3-4") are supplied with the kit. Had to run to hardware store to get new hose clamps for the inlet/outlet of the pump before intalling new one. Suggest new hose clamps be provided with the kit. Only thing that was not too clear in instructions was when reconnecting power wiring harness to motor. By looking closely at the instruction diagram I was able to locate what looked to be the right power extension harness from the bag of parts and attach it to the existing power wire harness and the new motor. Suggest also that you somehow better distinguish or identify the proper way the power wire harness should be fastned to the motor? The existing power wires were both the same color and both the female and male connections for the power at the new motor were identical leaving you to guess which wire goes to which connection. After re-installing dishwasher, put about a gallon of water in bottom of unit prior to starting and then put it through a few cycles. It has been working just like new. Suggest having a helper when removing and re-installing dishwasher from under kitchen counter to assist with the power cord, water line, drain line, and help to turn the dishwasher upside down and right side up again.

The Solenoid black plastic had melted around the solenoid shaft. I unplugged the solenoid, removed 2 screws,then one C clip and pulled the the unit out. The new solenoid is difficult to install all together as the shaft it goes on holds it all together when both springs are installed - - so I installed in one piece, with the 2 screws, except for the white plastic thing, the C clip that holds it on the shaft, and one of the two springs - - these three items went on separately. I wanted to thank the help your expert gave, but I couldn't figure how to do that.

Removed the lower rack and installed new wheels with clips

The newly purchased wheels have a little different design and could be installed in a matter of few seconds.

Disconnect water line and screws (2) holding dishwasher under cabinet, and clamp for wastewater line. Pulled dishwasher out, turned on its side, and removed pump. Disassembled pump per instructions (great instructions) and installed new parts. Reversed to reassemble and except for a loose clamp that leaked (I tightened) it went well. Just under 1 hour.

First I opened the package and screwed the new dispenser cap into place.

Inserted wheels on socket and then into the dishwasher rack.

Removed door panel. Removed old door seal and cleaned seal recess. Installed new seal. Replaced door panel on door and ran a cycle to check for leaks. Readjusted door latch to correct small leak. Ran another leak test. Job complete and wife is happy!

installed part on inside end of rail. no tools needed. original part wouldn't stay on rail. finished in 2 minutes
wife happy

Turn off power at breaker box.
Remove lower covers and 2 screws into counter top.
Verify sufficient length on water and electrical connection to allow sliding dishwasher out approx. 2/3. I disconnected the electrical at the j box on the dishwasher. If you must disconnect the water line, shut off supply, usually located under nearby sink, and provide a rag or sponge for small amounts of water left in supply line.
Carefully pull back the insulation to expose two screws on top where water line runs into the center.
Pull the top tray part way out and reach in to hold the spray arm while removing the screws. The spray arm will easily drop out.
Hold the new spray arm in place making sure the raised screw posts push into the holes, then reinstall the two screws. Done. Pull insulation back into place, retape if necessary. Reconnect electrical and water if necessary.
Slide unit back in, checking alinement. Rescrew to counter top and reinstall lower covers. Task complete. 15 mins if prepared. 30 mins if both elect. & water are disconnected and you are somewhat hesitant.

We knew roughly how we needed to put the cap on the rail, but our technique of simply forcing it in the end of the rail wasn't working. The trick is to bend the moveable part of the plastic cap inward while you're sliding it in, and it clicks right into place.

The location of the cap we were replacing was the upper back left, which made it a little tricky to reach back there and insert it, especially for a bigger guy like myself. We took the bottom rack out and my smaller wife was more easily able to lean in the dishwasher and reach back there to insert it.

The symptom was that none of the dishwashers light came on – it was totally dead
With this repair the important thing was making sure I was replacing the right part. I also tested parts in order to avoid disassembling more than I needed. I checked the following:
1. Circuit breaker
2. Electricity was getting to the connection box underneath the dishwasher. (Require removing panels between DW door and floor).
3. Next I disassembled the DW inner door and checked the switch. Power was getting to the switch. When depressed, power was go on both sides of switch.
4. I pulled out the electronic control assembly (ASM) and checked that power was getting to the ASM; it was. (Note: be careful about what you touch, there is 110 volts out in the open).
5. I pulled the ASM from the enclosing plastic box that surrounds it. I looked at the circuit board to trace where power went from the connector. Not surprisingly, it went through a fuse then to a transformer.
6. I checked the fuse two ways: I checked it hot: power was getting through the fuse. I also unplugged the power and checked the resistance. The fuse was good.
7. Set the Volt-Ohm meter back to 300 Volts AC range – do not risk putting 110 volts into the ohms setting.
8. 110 volts was getting to the primary side of the transformer. There was no voltage on the other side.
9. I unplugged the power and checked the resistance of the primary side of the transformer. It was “open” – meaning a wire is broken inside the transformer.
10. This confirms the problem in on the ASM board. If I knew the voltage on the secondary of the transformer and radio-shack had such a part I guess I could try unsoldering it and replacing it. But I didn’t know that and there were signs of water corrosion on the board so I replaced it.
11. PartsSelect made the look up easy. Delivery was fast. The DW now works again.

Removed dishwasher, took off motor, and ordered part. It was delivered in a timely fashion (3 days). Determined which directions to follow. Used screwdriver to hook up motor. Put dishwasher back into cabinet area, made sure there were no leaks before fastening the dishwasher in place. Took about 1/2 hour to complete process. Very satisfied.

Simply screwed in new cap

Read directions. They were poorly drawn. Set them aside. Opened up unit on December 26th. I made careful observation of the wiring, two hoses, one metal bracket, the hose two clamps, and then proceeded. Instructions said 1 to 2 hours, to complete. Ha Ha, perhaps if you've done it before. It was actually really closer to four hours. When done, it worked perfectly. The best part, my wife said: "This was the best Christmas present ever!" That made my day! Dishes are clean again, just like new! Thank you: www.PartsSelect.com.